Search results for: 'Application No'

The IDEC CS-10 ACSSO contact block is a cam switch component configured with one normally open contact and circuit designation C-2004. It is rated for 600 V insulation voltage and 10 A thermal current, utilizes silver contacts, and is designed for industrial control applications requiring reliable mechanical switching performance.

Eaton XTCEXFAC20 auxiliary contactor supports control-panel auxiliary switching with two normally open contacts and visible AC/DC ratings.

The General Electric 8G163WF is a fluorescent lamp ballast labeled for 277-volt operation and F48CW lamp applications. This unit is identified directly from manufacturer carton labeling and is supplied as a single ballast. No additional accessories or documentation are included.

The Allen-Bradley 800T-XA2 Series D is a 30 mm industrial control contact block featuring two normally open contacts and an A600 NEMA pilot duty rating. Designed for use with Bulletin 800T operators, it provides screw-terminal connections and base-mount installation for industrial control panels.

The GE IC2956A206A is an industrial interlock snap-action contact block used as a control component within safety and machine control systems. This unit is a standalone mechanical contact block featuring a snap-action mechanism for consistent contact switching. No additional accessories or hardware are included.

Allen-Bradley 100-C12ZA10 3-pole contactor brings IEC motor-control switching with a 220V DC coil, 1 NO auxiliary contact, and marked AC load ratings.

Square D 2510KG1 manual switch delivers reliable 30A control for single-phase systems with a 2-pole toggle design and non-reversing operation in a compact NEMA 1 enclosure.

The Telemecanique XSAV32373 is an inductive proximity sensor designed for rotation monitoring applications. It features a cylindrical M30 nickel plated brass housing, 10 mm nominal sensing distance, PNP output with 1 NC function, and operates on 12 to 48 V DC. The sensor includes a fixed 2 meter cable connection and is rated IP67.

The Telemotive E7207-1 Circuit Board is an industrial automation component used in Telemotive radio control systems. Identified by part number E7207-1, this board is commonly applied in industrial control environments including crane and hoist remote control systems.

Square D 9001 TS-1 selector switch operator delivers 2-position manual control for industrial panel systems requiring reliable mechanical switching input.

IPC 005-4240 power resistor delivers 110 ohm resistance with 800W heat dissipation for dynamic braking, load testing, and industrial energy control applications.

The IDEC APW299D-W-120V is a panel-mount white pilot light indicator designed for industrial control applications. This unit operates on 120V AC and features a dome-style white lens with a metallic bezel. It is UL listed and CSA marked, with screw terminal connections housed in a compact rectangular base.

The Thermo Environmental 2200-0-010 Heater Control Module (P/N 22000010) is an industrial control board designed for regulated heater management within environmental and analytical systems. This module functions as a temperature control component in Thermo Environmental instrumentation platforms.

The Murr Elektronik 23050 is a three-phase RC motor suppressor designed to reduce induced voltage peaks in AC motor applications. Rated for up to 575 VAC at 50/60 Hz and 4 kW engine power, it supports star-connected RC suppression and installation close to the interference source.

Allen-Bradley 1756-L55/A ControlLogix 5555 processor supplied with a 1756-M13/A 1.5 MB memory expansion module. This controller requires external memory for operation and installs in a ControlLogix chassis for high-performance industrial automation systems.

The General Electric CR104PLT43 is a 30.5mm push-to-test indicator light designed for 240V AC industrial automation systems. Part of the GE CR104P series, it utilizes a resistor power supply and supports machine-tool and control panel applications where manual lamp verification is required.

The Omron MY4Z DC24(S) is a general-purpose miniature power relay with a 4PDT contact configuration and 24 VDC coil. Rated for 5 A switching in four-pole applications, it is designed for sequence control and power switching in industrial control systems.

The Allen-Bradley AK-R2-360P500 Dynamic Brake Resistor is an external medium-duty resistor kit designed for PowerFlex 70 and 700 series drives. It provides 360 ohms of resistance with an 86 watt continuous power rating to dissipate regenerative energy during motor braking.

OMRON PTF11PC 11-pin relay socket lot with 10A rating and screw-terminal wiring layout, ready for relay socket replacement, panel support, or control component stocking.

Hubbell HC69476733 industrial resistor assembly delivers controlled resistive load handling for power dissipation and current regulation in industrial electrical systems.

Omega CN9111A temperature controller delivers precise thermal regulation with dual relay outputs and 115V operation, supporting controlled heating and cooling processes across industrial environments.

The Square D 8501NR61 is an 11-pin plug-in relay socket designed for use with compatible Square D relays and timers. It features single-tier screw clamp terminals and supports both panel and DIN rail mounting for industrial control applications.

Eaton Cutler-Hammer SL7-BL120-R delivers high-visibility red LED signaling in a 70 mm stacklight format, operating on 120VAC for industrial status indication and machine signaling applications.

Helwig Carbon H704 high-speed turbine carbon brush is built for turbo generator service, delivering low-friction electrical contact, balanced current distribution, and dependable performance at peripheral speeds up to 180 mph.

SOR 4N3-KK4-N1-C1A-ZZ pressure switch delivers adjustable 2-25 PSI switching for industrial pressure control, with 750 PSI over range and 1000 PSI proof pressure for monitored process applications.