Search results for: 'action cost'

Fluke Networks MMC-62-SCSC Launch Cable is a multimode SC/SC fiber optic cable, is used for high-speed networks installation, inspection and troubleshooting. An OTDR requires launch cables or fiber rings to measure the end-to-end loss of fiber optic links. The multimode fiber has a 62.5/125µm core/cladding diameter.Length is 105 meters.

Multimode launch cable 50μm SC/SC. Fluke Networks MMC-50-SCSC Launch Cable is a multimode SC/SC fiber optic cable which is used for high-speed networks installation, inspection and troubleshooting. The multimode fiber has a 50/125µm core/cladding diameter. Length is 105 meters.

The V-2410 Three-Way Multipurpose Solenoid Air Valve is used in applications where an electrical circuit operates a pneumatic control device. This valve diverts the air signal to the pneumatic device when the coil is energized or de-energized, depending on the choice of air connection.

The 42N50A-30 coaxial fixed attenuator provides 30 dB attenuation and a 50 watt power rating for high power measurements.Fixed attenuator30 dB attenuation50 watt power rating

The TPP0250 is a Passive Voltage Probe designed for use with Tektronix MDO3000, MDO4000B, MSO/DPO4000B and MSO/DPO5000B-series oscilloscopes, these probes provide up to 1GHz of analog bandwidth with less than 3.9pF of capacitive loading. Integrated oscilloscope and probe measurement system provides intelligent communication that automatically scales and adjusts units on the oscilloscope display to match the probe attenuation.

Greystone - Sensor Type 12 - Pt1000-1000 ohm Platinum RTD. Immersion 100mm (4") c/w ABS utility box -requires thermowell Probe Sensors. The TE200 Series temperature sensors offer a choice of precision platinum RTD's, IC's, or NTC thermistor sensors which can be interfaced with a computerized monitoring or control system.

Schneider Electric’s remote racking Masterpact NW circuit breakers is designed is reduce the arc flash safety hazard for personnel during installation, startup and maintenance procedures. The Masterpact NW remote racking device provides maintenance personnel the ability to rack a low-voltage draw-out breaker from a remote location. This allows the personnel to be clear of the arc flash boundary area.

Inline Ratcheting Head for Low Profile Hydraulic Ratcheting Wrenches Inline IU-XL.

Inline Ratcheting Head for Low Profile Hydraulic Ratcheting Wrenches Inline IU-XL.

Inline Ratcheting Head for Low Profile Hydraulic Ratcheting Wrenches Inline IU-XL.

Fujikura FSM-50S SM MM Fiber Core Alignment Fusion Splicer w/ Cleaver CT-30 50 S

The Ti200 infrared camera delivers the flexibility and performance to allow you to stay on top of innovation, whether it's through industrial or commercial applications. You'll be able to spectrum analyze, detect heat and radiation level variations, or use it for industrial process control — all with wireless speed and ease. And, since it's future-ready, no matter what comes next for your business, so long as you have an infrared camera on hand, you'll be ready.

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

The DSX-PLA004/CHA004 permanent link and channel adapters meet all measurement accuracy specifications for Level IV test equipment. The life of module contacts is >5,000 cycles. Dimensions are 3.0 in x 2.1 in x 1.2 in (75 mm x 54 mm x 30 mm). The permanent link adapter has a 4.85 ft (1.48 m) ±0.25 ft (0.1 m) cable. Weight is ~2.4 oz (68 g) for the channel adapter and ~11.7 oz (332 g) for the permanent link adapter.

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

The DTX-MFM2 fiber module are used with a DTX Series Cable Analyzer to test and certify fiber optic cabling installations. 

The Adam Equipment 3126011281 ATP Thermal Printer Paper Pack of 10 is the perfect solution for those who need to replace the thermal printer paper for their ATP thermal printer. With this pack of 10 rolls, you can be sure that you always have a fresh supply of paper on hand, ensuring that your printer is always ready to go when you need it. Each roll is made with high-quality materials to ensure that your prints are clear and legible every time. Don't let a lack of thermal paper hold you back - order your pack of 10 rolls of ATP thermal printer paper today.

Viken Pb200e XRF Lead Paint Analyzer: Portable, HUD-certified device for fast, accurate lead detection with non-destructive testing, GPS, and built-in camera.

Megger DLRO10HD Product Overview

Product Overview

Product Overview

The CFP2-100-Q CertiFiber Pro Quad Optical Loss Test Set (OLTS) helps cabling professionals accomplish more than ever and comes with a Wi-Fi adapter for wireless connectivity to Fluke Networks LinkWare Live software. It's all about accurate, error-free certification, making jobs easier to manage and certifying fiber optic cabling to industry standards, faster.

VIEW5 PRO’s 5-inch high-resolution color LCD touch screen with user-friendly intuitive GUI (Graphic User Interface) offers large and clear fiber images to users. By double-tapping the screen, users can Zoom In & Out the image to the world’s highest magnification of 520x. The fusion splicer is equipped with bua ilt-in IoT module that connects to the INNO’s View Pro Cloud Management System for real-time operation and management online. This innovative cloud-based solution is designed to create the most advanced and yet most uncomplicated splicing and work experiences ever.

The 170ADO53050 is a Discrete Solid State I/O Base used in Modicon Momentum automation platform modular in design. The communication adapters and processor adapters are designed to work as functional modules when they are snapped onto a Modicon Momentum I/O base. This I/O base requires that some type of Modicon Momentum adapter be attached before it can be functional. I/O bases fit into compact standard housings that can be mounted on a DIN rail or on panels in a cabinet. It read information from field sensing devices and control discrete and analogue field actuating devices. Terminal blocks and bus bars are available for use with the bases so that this base can be used to support 2, 3 and 4-wire field devices. I/O field devices and the power supply to the module are connected via three 18-pin terminal blocks and an optional 1, 2 or 3-row busbar. This I/O base supports the rest of the control system.