Search results for: 'mounted'

Square D 9001 TS-1 selector switch operator delivers 2-position manual control for industrial panel systems requiring reliable mechanical switching input.

Allen-Bradley 1771-A1B/B is a 4-slot PLC-5 I/O chassis designed to house processors, power supplies, and 1771 I/O modules, providing reliable backplane connectivity for panel-mounted industrial control systems.

Pomona 5143-K-48 SMD test tweezer enables fast, precise surface-mount device testing with durable tips, banana plug connection, and a 48-inch cable.

The Corcom NF21091-3 is a chassis-mount EMI line filter rated for 16 A at 250 VAC, 50/60 Hz. This metal-enclosed filter features clearly labeled LINE and LOAD terminals and is designed for installation in AC power input paths where conducted electrical noise reduction is required.

ABB IEMMU11 module mounting unit provides rear-mounted chassis support, power distribution, and backplane communication for up to 12 INFI 90 OPEN Symphony control system modules.

Pomona 3846 BNC female to female panel mount coupler with isolated ground, designed for secure panel installations requiring 50-ohm impedance and electrical isolation between shell and flange.

The ATC TDH-120-ALA-100 is a delayed interval time delay relay designed for industrial control applications. It operates on 120 VAC/DC supply voltage and provides an adjustable delay range from 1 to 100 seconds using dual front-mounted dials. The relay features a plug-in octal base and relay contacts rated at 10A.

BROSA EBM 6111 load cell delivers 100 kN force measurement for felt tension control and industrial monitoring, with a flange-mount design and integrated cable for fixed installation.

The Honeywell 620-1690 is a processor rack chassis used in the legacy IPC 620 / ISSC 600 PLC system. It provides the physical backplane and power distribution framework for processor, I/O, and communication modules in rack-mounted industrial control installations.

Wohler Supplementary Light 4194 adds detachable illumination for a 2 in Wohler camera head in the VIS 400 modular inspection system, helping bring inspection areas into clearer view during flue, drain, and ventilation camera work.

Eagle Eye Power Solutions VS-Series ventilation system provides 1050 CFM forced-air exhaust for battery rooms, helping purge hydrogen and other gases.

The Yamatake Honeywell J-DOM10 is an industrial I/O module identified by the manufacturer marking “J-DOM10.” The unit features a 32-position screw terminal block and front-panel status indicators labeled RDY and ACT. Manufactured in Japan, this module is a legacy component commonly encountered in installed industrial control systems.

Leviton 065-4729-C delivers industrial-grade 15A, 125V locking connection performance with NEMA L5-15R grounding, 2-pole/3-wire wiring, nylon construction, and 18–10 AWG termination support.

Used Sonatest PMAP3737445T, 5 MHz 0.375" 45° angle beam probe for weld inspection, flaw detection, and code-compliant NDT. Compatible with Sonatest Wave, Sitescan D-50, Masterscan D-70. Buy from Cartoli or call 1-833-322-7865.

Thomas & Betts Red Dot 2CCD weatherproof two-gang duplex receptacle cover delivers die-cast metallic protection for dual duplex outlets with gasketed sealing and device-mount installation.

The Mitsubishi CP30-BA 1-Pole 5A M-Curve Circuit Protector is a compact DIN-rail-mounted supplementary protector designed for low-capacity control circuits. It features a medium-speed hydraulic-magnetic tripping characteristic, 5 A current rating, and supports AC 250 V or DC 65 V operation in industrial control panels.

Used Waygate Technologies Gamma 5.0/50 5.0 MHz 0.50" straight beam ultrasonic transducer featuring a side-mounted Microdot connector. Designed for precise flaw detection and material inspection on thick plates, forgings, and castings. Fully tested and certified for reliable NDT performance.

The C3 Controls DDS2-340-DHGRY is a non-fused, 40 amp, 3-pole disconnect switch designed for door-mount applications. It features a red/yellow rotary operating handle and an IP65 ingress protection rating for use in industrial control environments requiring reliable circuit isolation.

PDQ 6200R-01 wide stile rim exit device for 36" doors in US32D finish. Panic rated, reversible, and built for commercial duty applications.

Allen-Bradley 800H-JP2KB7AAXX hazardous location selector switch from Bulletin 800H. This is a 3-position, non-illuminated, maintained standard knob operator with KB7 standard cam and AAXX contact block configuration.

Westinghouse 9966D75G01 IQ Data Plus II power monitoring display delivers three-phase electrical measurement including amps, volts, watts, power factor, and energy data for digital metering systems.

The General Electric CR305X100E is a side-mounted auxiliary contact adder block providing one normally closed (1 NC) contact for GE 200- and 300-Line starters and contactors. It is designed for field installation onto a basic auxiliary contact block and is rated up to 600 VAC and 250 VDC.

General Electric 36A352951 AC-A circuit board with tag 356X479TAG01, designed for industrial control systems requiring analog AC signal processing within GE automation and power control platforms.

Schneider Electric AS-212P-010 Modicon discrete input module provides 12 PNP 24VDC inputs for legacy Modicon PLC systems, enabling reliable sourcing-signal interface from industrial sensors and switches.

The INNO Instruments UN1COMK UN1CO Mobile Smart Tray Kit is a portable workstation designed for fiber optic fusion splicing in elevated and field environments. The UN1CO Mobile Kit supports wearable, tripod, ladder, and pole-mounted configurations for field-based fiber installation work.