Search results for: 'openzl'

Tests for correct wiring, open ground, reverse polarity, open hot, open neutral, hot on neutral, hot and ground reversed with open hot and ground fault interruption in 3‑Wire, 120Volt AC.

Allen-Bradley 800E-3X10 is a latch-mounted normally open contact block for 22.5 mm 800E pilot devices, delivering reliable 10A switching for industrial control and signaling circuits.

The Allen-Bradley 800T-XA2 Series D is a 30 mm industrial control contact block featuring two normally open contacts and an A600 NEMA pilot duty rating. Designed for use with Bulletin 800T operators, it provides screw-terminal connections and base-mount installation for industrial control panels.

ABB IEMMU11 module mounting unit provides rear-mounted chassis support, power distribution, and backplane communication for up to 12 INFI 90 OPEN Symphony control system modules.

Hubbell HC69476733 industrial resistor assembly delivers controlled resistive load handling for power dissipation and current regulation in industrial electrical systems.

Allen-Bradley 700-P200A1 is a NEMA heavy-duty industrial relay with a 110–120VAC coil and two normally open contacts, designed for reliable switching in machine tool and demanding control applications.

The IDEC CS-10 ACSSO contact block is a cam switch component configured with one normally open contact and circuit designation C-2004. It is rated for 600 V insulation voltage and 10 A thermal current, utilizes silver contacts, and is designed for industrial control applications requiring reliable mechanical switching performance.

Square D 83713 9070EO2D1 delivers open-type control circuit transformer operation with multi-tap primary input, 110/115/120 V secondary output, and 50/60 Hz ratings for industrial control panels.

Product Overview

Fluke TS19 Test Set: Reliable network testing with open/short circuit detection, tone operation, polarity check, and monitor mode for safe diagnostics.

Eaton XTCEXFAC20 auxiliary contactor supports control-panel auxiliary switching with two normally open contacts and visible AC/DC ratings.

Fluke T6-1000PRO electrical tester uses FieldSense technology to measure true RMS AC voltage and current up to 1000V and 200A through an open fork for faster, safer troubleshooting.

AEMC 2130.60 100 ft Tape Measure provides extended distance measurement capability for ground resistance testing setups and related field measurement tasks requiring 100 ft reach.

Four piece set. Ideal for most brands of smart phones, video games, notebooks, electronic devices. Use to open, pry and disconnect small electronic components without damaging housing or parts.

Fluke T5-1000 tester measures voltage, continuity, and current up to 100 A with OpenJaw design and Slim Reach probes for tight spaces.

Amprobe PK-110 kit includes a digital multimeter, GFCI socket tester, and non-contact voltage probe for safe residential voltage and wiring checks.

Fluke LinkIQ LIQ-KIT-3PACK – Bundle of 3 Cable+Network Tester kits. Each tester verifies Cat6A/10G LAN cabling, performs PoE tests, and provides switch diagnostics. Includes IntelliTone® Pro 200 probe for cable tracing, remote ID, cords, charger, and carrying case.

Johnson Controls P10BC-7C low pressure control, SPDT, 1-stage, 3 to 20 psi range, 12 psig factory setting, 2 psi switch differential, with barbed fitting.

Application D-subminiature contacts, RS232 pins & sockets AWG 30-18 Open Barrel contacts (Molex/AMP style)

The GE Fanuc IC660BBR101 is a Genius I/O relay output block providing 16 normally open relay outputs. Designed for distributed control systems, it supports 115/230 VAC block power, individual output status LEDs, and compatibility with a wide range of low-power AC and DC control devices.

Application: Open barrel contacts D-sub, Molex, AMP Style Pin

Application: Open barrel contacts D-sub, Molex, AMP Style Pin

The Amprobe MO-100 Milliohm Meter offers accurate four-terminal resistance measurement with auto-hold, overvoltage protection, and a portable battery-powered design.

Fluke Networks LinkIQ LIQ-KIT Cable+Network Tester – Verifies cable performance up to 10G, measures length, maps wiring, and identifies faults. Provides key network diagnostics including switch details (speed, duplex, VLAN). Includes remote ID, cords, adapters, and carrying case.