Search results for: 'Application No'

The Turck B8241-0/PG9 is a field-wireable M12 right-angle, 4-position female connector designed for sensor and actuator wiring in industrial automation. It uses a screw terminal connection, supports 250 V at 4 A, and accepts PG9 cable glands for secure, sealed installations.

Allen-Bradley 1336-CAP-SP3-A DC bus capacitor assembly designed for 460V 1336 PLUS, FORCE, and IMPACT drives. Supports stable DC bus operation in compatible 25–30 HP drive systems.

Allen-Bradley 1336-RLOAD-SP1A load resistor for Bulletin 1336 AC drives, designed to manage internal load, DC bus discharge, and power stabilization in 25–30 HP, 460V drive systems.

ABB IEMMU11 module mounting unit provides rear-mounted chassis support, power distribution, and backplane communication for up to 12 INFI 90 OPEN Symphony control system modules.

Cooper Bussmann MV055F1DAX100E is a 5.5kV full-range medium voltage fuse rated at 100A with 50 kA RMS symmetrical interrupting capacity for feeder circuit, switchgear, and transformer protection.

AmRad RA200044-505 capacitor delivers reliable 5.0 MFD motor performance for HVAC and compressors; legacy model replaced by USA2029 for long-term durability.

Kanson Electronics 1010-1-J-2 off-delay timer relay delivers adjustable 0.5 to 50.0 second timing with 115V 50/60Hz operation and 10 amp output switching for industrial control circuits.

SKF CMSS65-010-00-12-10 is a CMSS 65 series 5 mm eddy current probe with armored cable, 1/4-28 threaded fully threaded case, 3.0 cm case length, and 1.0 m overall length.

The ABB OHDI-01 is a 115/230 VAC digital input module designed for use with ABB ACS550, ACH550, and ACS800 drives. It converts high-voltage digital input signals to 24 VDC drive inputs and supports up to six 115 VAC inputs or three 230 VAC inputs.

Siemens 771-8STF1 current-to-pneumatic (I/P) transducer converts a DC mA input to a proportional pneumatic output. Configuration: 4–20 mA input, 3–27 psig output, standard output capacity, terminal strip, intrinsically safe approval.

The GE Fanuc IC693CHS392G is a 10-slot expansion I/O baseplate for the Series 90-30 PLC platform. It features a 25-pin D-type expansion connector, rack address DIP switch, and supports local I/O expansion up to 50 feet. Designed for use with compatible CPU baseplates.

The KAMAN Sensors digiVIT 855949-000 is a self-tuning digital driver for non-contact inductive and eddy current position and displacement sensors. It features pushbutton calibration, embedded intelligence, selectable analog outputs, and Ethernet connectivity for monitoring and parameter switching.

The MIP LM 3086 EPA3 is a laser-based opacity and dust monitor designed for continuous emissions monitoring in industrial stacks. It uses a single-pass, dual-path laser architecture with an optical reference path to measure opacity, optical density, and calibrated dust concentration values.

Honeywell 380-01873-100 I/O Interface Module enables remote monitoring and control of field devices using RS485 Panel Bus™ communication with 34 configurable I/O points for scalable building automation systems.

The General Electric DS200DDTBG2ABB is an LCI Auxiliary I/O Terminal Board for GE Mark V Speedtronic gas and steam turbine control systems. It provides auxiliary signal termination, conditioning, and isolation for analog and digital I/O in high-voltage industrial control environments.

This CCC Series 4 temperature input module set includes one IOM TCW (I-1/201-2/200) and one EIOM TCW (E-1/202-3/200). Both modules are designed for 3-wire GDC RTD temperature inputs and chassis mounting within CCC Series 4 control systems.

Allen-Bradley 813S-V0WE line voltage monitor relay designed for three-phase systems to detect phase loss, phase reversal, and voltage unbalance, providing automatic protective signaling in motor control circuits.

Allen-Bradley 50388 Driver PCB Board provides signal conditioning and drive interface control for compatible Allen-Bradley automation systems, supporting reliable communication between logic modules and field devices.

Metso Automation PDP406 Distributed Processing Unit for MAX DCS delivers real-time control, alarming, and data processing for industrial automation systems requiring reliable distributed architecture.

Allen-Bradley S50403 driver board designed for 1334 series AC drives, supporting 30–50 HP motor control. This replacement PCB regulates motor speed and torque through controlled voltage and frequency output.

Allen-Bradley 800H-R3HA7 explosion-proof selector switch station with HAND-OFF-AUTO operation, built in a Type 7 & 9 aluminum enclosure for Class I, II, and III hazardous industrial locations.

Allen-Bradley SP-135893 is a precharge SCR firing circuit board kit for 1336 series 75 HP drives, supporting controlled DC bus charging and reliable drive startup in industrial motor control systems.

Ronan X96-1000CB R14 is the core control board for X96S microprocessor systems, processing detector signals and enabling modular I/O and industrial communications for measurement applications.

Allen-Bradley 1336-L-SP12A power module ensures stable input power for 1336 AC drives, supporting high-horsepower operation with reliable line conversion performance.

Eaton 6-22-2 restores performance in Citation Series Size 0 contactors with OEM 3-pole replacement contacts for reliable motor control and long-term durability.