Search results for: 'opened'

Eaton C25BNF220A delivers reliable 20A motor switching with a 120V coil, ideal for HVAC, refrigeration, pumps, and industrial control panels.

Thomas & Betts Red Dot 2CCD weatherproof two-gang duplex receptacle cover delivers die-cast metallic protection for dual duplex outlets with gasketed sealing and device-mount installation.

Kanson Electronics 1010-1-J-2 off-delay timer relay delivers adjustable 0.5 to 50.0 second timing with 115V 50/60Hz operation and 10 amp output switching for industrial control circuits.

Square D 2510KG1 manual switch delivers reliable 30A control for single-phase systems with a 2-pole toggle design and non-reversing operation in a compact NEMA 1 enclosure.

The Struthers-Dunn W88AHPX-36 is a hermetically sealed 3PDT plug-in relay from the 88HP Series, rated 10A and configured for 120VAC operation. It features an 11-pin octal base and a sealed gray metal enclosure designed to prevent contamination and corrosion.

The Fluke CV301 is a 3 in (75 mm) ClirVu® infrared inspection window with a security key door latch. Designed for permanent installation on electrical enclosures, it enables infrared inspections without opening panel doors while maintaining enclosure ratings and safety compliance.

The Hammond Power CRX06D1BC is a three-phase iron core line reactor rated for 600 VAC and 6.1 A. Part of the HPS Centurion® R Series, it provides controlled impedance to mitigate harmonics and electrical transients in AC drive systems operating at 50/60 Hz.

The Allen-Bradley AK-R2-360P500 Dynamic Brake Resistor is an external medium-duty resistor kit designed for PowerFlex 70 and 700 series drives. It provides 360 ohms of resistance with an 86 watt continuous power rating to dissipate regenerative energy during motor braking.

Fluke AC220 SureGrip alligator clips provide insulated, high-voltage test lead connections for electrical measurements. Designed for use with TL222 and TL224 leads, offering secure gripping on conductors and terminals.

Fluke 050-CLKT infrared window enables safe thermal inspections through live panels, featuring a 2-inch arc-resistant CLIRVU crystal and Kwik Twist cover.

Fluke GFL-1500 solar ground fault locator pinpoints active PV faults up to 1500V using non-contact signal tracing for faster, safer troubleshooting.

Allen-Bradley 802X-B4 watertight limit switch with top push rod actuator and snap-acting 1NO/1NC contacts. Built for reliable position sensing in harsh industrial control applications.

Allen-Bradley 813S-V0WE line voltage monitor relay designed for three-phase systems to detect phase loss, phase reversal, and voltage unbalance, providing automatic protective signaling in motor control circuits.

Fluke PRV240FS provides a safe 240 V AC/DC source to verify FieldSense testers, multimeters, and clamp meters before and after live measurements.

Fluke T5-H5-1AC Kit: Compact, versatile electrical tester for voltage, current, and continuity with OpenJaw™ and Slim Reach™ probes.

Amprobe LAN-1 Cable Tester: Reliable LED cable verification tool with continuity, shorts, miswire detection, and remote testing for network installers.

The Wohler Residential Air Duct & Dryer Vent Cleaning Set pairs rotary duct and dryer vent cleaning tools with VE 400 HD inspection for cleaning, viewing, and documenting residential duct conditions.

The Amprobe AT-6010 Advanced Wire Tracer Kit is designed to trace energized and de-energized wires, identify breakers and fuses, and locate shorts or opens. The kit includes a receiver with large LCD display and transmitter supporting operation up to 600 V AC/DC in CAT III environments.

The Fluke CV300 is a 75 mm ClirVu® infrared window with a hand turn door latch, designed to improve electrical inspection safety. It enables thermal inspections without opening energized panels and supports fast single-hole installation while maintaining enclosure ratings.

The Phoenix Contact PSR-SCF-24UC/URM/2x21 is a safety coupling relay designed for safe switch-off applications in industrial control systems. It features two force-guided changeover contacts, 24 V AC/DC supply voltage, and supports safety category 1, PL c, and SIL 1 applications.

The Mitsubishi SR-T5 AC100V 3A2B contactor relay is designed for control circuits requiring reliable auxiliary switching. It operates on a 100–127 VAC coil and provides 3 normally open and 2 normally closed contacts. The compact design supports DIN rail or screw mounting.