Search results for: '200 4'

INNO Instrument FH-12F Fiber Series ribbon fiber holder for 12-fiber flat ribbon cable, supporting 200 µm and 250 µm coatings and compatible with View12R, View12R-200, and View12R PRO detachable setups.

The INNO Instrument Ribbon Holder are fiber ribbon holders designed for use with INNO Instrument View12R and View12R PRO fusion splicers. The holder supports 250 µm ribbon fiber during the splicing process, maintaining fiber alignment and stability within the splicer. Its detachable design allows quick installation and removal when preparing ribbon fibers for fusion splicing.

High quality bit at an economical price Made from S-2 tool steel with a hardness of HRC 59°~ 61°

High quality bit at an economical price Made from S-2 tool steel with a hardness of HRC 59°~ 61°

High quality bit at an econom Made from S-2 tool steel with a hardness of HRC 59°~ 61°

INNO Instrument FH-Single Fusion Series fiber holder for 900 µm single fiber in detachable M Series fusion splicer applications.

Fisher Water Level Indicator measures groundwater in wells and boreholes. It features a flexible probe, depth-marked cable, and LED/audio alerts for accurate water level detection.

This CCC Series 4 temperature input module set includes one IOM TCW (I-1/201-2/200) and one EIOM TCW (E-1/202-3/200). Both modules are designed for 3-wire GDC RTD temperature inputs and chassis mounting within CCC Series 4 control systems.

Adam Equipment ASTM 4 200g Weight: Durable stainless steel calibration weight for precise scale calibration. ANSI/ASTM compliant with plastic case.

Delivers fast point-to-point continuity testing for grounded pathways and long-distance connections with polarity reversal, lead compensation, programmable thresholds, and 300 V CAT IV safety.

The General Electric DS200DDTBG2ABB is an LCI Auxiliary I/O Terminal Board for GE Mark V Speedtronic gas and steam turbine control systems. It provides auxiliary signal termination, conditioning, and isolation for analog and digital I/O in high-voltage industrial control environments.

Siemens TM-E15C24-01 terminal module for ET 200S provides secure spring wiring, supports pre-wiring, and pairs with all 15mm ET 200S electronic modules.

Fluke 190-204-III is a 4-channel portable ScopeMeter oscilloscope with 200 MHz bandwidth, isolated inputs, WiFi and USB connectivity, built for high-voltage industrial signal troubleshooting.

Allen-Bradley 200-EX640Z1 instantaneous control relay with a 115–125VDC coil, designed for reliable multi-pole switching. Features 6 normally open and 4 normally closed contacts for industrial control logic.

Fluke 190-204-III CAL ScopeMeter offers 200 MHz bandwidth, four isolated channels, deep memory, and traceable calibration for advanced industrial troubleshooting.

The Rohde & Schwarz FSH-Z44 directional power sensor is compatible with FSH handheld analyzers and supports 200MHz–4GHz forward and reverse RF power measurement from 30mW to 120W for transmitter and antenna testing.

Hilti PS 300 Ferroscan Concrete Scanner Kit helps locate rebar, measure cover, estimate bar diameter, and refine scan analysis with PSA 200 Monitor Tablet, PROFIS Detection, and Expert Mode control.

Product Overview

Fluke T6-1000PRO electrical tester uses FieldSense technology to measure true RMS AC voltage and current up to 1000V and 200A through an open fork for faster, safer troubleshooting.

LEM USA HAL 200-S Current Transducer: Precision 200A Hall Effect sensing for industrial power systems. Compact, efficient, and high immunity to interference!

Fluke i200 AC current clamp enables accurate 0.5–200A AC measurements using a multimeter. Features 1 mA/A output, banana plug interface, and CAT III 600V safety for electrical testing.

Digi-Pas DWL-200 Torpedo Digital Level delivers fast digital angle and slope measurement with 0.1° resolution, alternate zero, inverted display, self-calibration, and magnetic hands-free positioning.