Search results for: 'sporttik'

The Fluke i400s AC Current Clamp extends current measurement capability for multimeters, power quality analyzers, and oscilloscopes. It supports AC current ranges from 0.5 A to 400 A with dual output scaling and a compact clamp design rated for CAT IV 600 V environments.

Fluke 1535 Insulation Resistance Tester delivers 250V–2500V testing with insulation measurements up to 500 GΩ. Designed for industrial and solar environments with CAT IV 600V safety and automatic PI/DAR calculations.

Amprobe ACDC-100 clamp-on multimeter measures high AC/DC current with inrush capture, capacitance testing, and a large easy-to-read display.

Fluke 80i-2010S measures up to 2000A AC/DC on large conductors, enabling safe current testing without disconnecting the load.

Eagle Eye GFM-100 battery ground fault monitor with color touchscreen, Ethernet web interface, Modbus TCP/IP, and 4 Form C contacts for real-time monitoring of DC battery systems.

INNO Instrument SPA6000 is a modular power analyzer with a 12.1-inch touchscreen, support for up to four input modules, 512GB internal storage, and AC/DC power measurement bandwidth from DC to 5MHz.

Modicon AS-P120-000 delivers reliable 24VDC power for Compact 984 PLC systems, supporting stable control performance and legacy system continuity.

Fluke 1555 FC KIT insulation resistance tester delivers digital testing up to 10 kV with IR3000FC wireless connectivity, onboard data storage, and advanced diagnostic measurements for high-voltage electrical assets.

Amprobe AMP-320 clamp meter measures 600 A AC/DC with True RMS, temperature, motor rotation, inrush current, and HVAC-ready diagnostics.

Amprobe 37XR-A digital multimeter delivers True RMS accuracy with component and logic testing, backlit display, and CAT III 600 V safety.

Fluke FEV150 BASIC EV charging station analyzer tests safety and performance of AC chargers with guided workflows and control pilot simulation.

Fluke FLK-393-IRR-PVLEAD solar PV test kit measures up to 1500 V DC, AC/DC current, and solar irradiance for safe photovoltaic installation and maintenance.

AEMC PowerPad III power quality analyzer supports electrical diagnostics, power monitoring, harmonics, alarms, transients, and energy analysis for single- or three-phase networks.

Fluke 381 clamp meter: Remote display and iFlex probe enable safe AC/DC current, voltage, resistance and frequency measurements in tight, noisy panels.

The Fluke 87V MAX Digital Multimeter Solar PV Lead Kit combines the IP67-rated 87V MAX True-RMS multimeter with Pomona PVLEAD1 MC4 solar PV connector test leads. Designed for electrical troubleshooting in harsh environments, it supports AC/DC voltage up to 1000 V, 10 A current, resistance, capacitance, frequency, and temperature measurements. The included MC4 to 4 mm leads enable direct voltage verification on photovoltaic arrays while maintaining IEC / EN 61010-031 compliance.

The Fluke i310s AC/DC current clamp is a Hall Effect-based probe designed for non-intrusive current measurement with oscilloscopes and multimeters. It supports AC and DC current measurement up to 450 A peak, with a frequency range from DC to 20 kHz and dual selectable ranges for measurement flexibility.

Fluke 1550C Insulation Resistance Tester delivers digital insulation testing up to 5 kV with DAR/PI calculations, long battery life, and Fluke Connect support.

AEMC C.A 6240 digital micro-ohmmeter for precise low-resistance and contact resistance testing. 4-wire Kelvin measurement with selectable test currents up to 10A, 1 µΩ resolution, onboard memory, and DataView® software support.

Fluke 190-204-III CAL ScopeMeter offers 200 MHz bandwidth, four isolated channels, deep memory, and traceable calibration for advanced industrial troubleshooting.

The Fluke PRV240 is a portable, battery-powered proving unit that supplies a stable 240 V AC/DC source to verify multimeter and tester operation before and after energized work. It helps meet safety requirements, reduces risk, and ensures instruments are functioning properly in the field.

The Fluke LIQ-KIT-87-5 Electrical & Network Troubleshooter Kit combines the LinkIQ Cable+Network Tester, IntelliTone Pro 200 probe, and Fluke 87V Industrial Multimeter in a single field-ready solution. It qualifies copper cabling up to 10GBASE-T using frequency-based measurements, performs switch and Ping diagnostics, and validates PoE negotiation and load delivery. The integrated multimeter supports electrical troubleshooting across industrial environments.

10A low-resistance tester with instantaneous, continuous, and automatic test modes for precise plant and field measurements.

AEMC 6505 Megohmmeter: Portable insulation tester with digital and analog bargraph, auto DAR/PI, backlight, and 500V to 5000V test voltages.

The Fluke 80I-110S is an AC/DC current probe with BNC output designed for use with oscilloscopes, ScopeMeter test tools, power harmonics analyzers, and multimeters equipped with BNC inputs. It supports current measurements from 0.1A to 100A DC and 0.1A to 70A AC, with switchable 100mV/A and 10mV/A output settings. The probe provides 1Hz to 20kHz bandwidth, 600V AC rms working voltage, and accommodates conductors up to 11.8 mm in diameter.