Search results for: 'checks is'

An OTDR launch cable, which connects the OTDR to the link-under-test, discloses the insertion loss and reflectance of the near-end connection. It is often available on a small spool or within a “launch box”, which is used to create the proper conditions for testing another similar optical fiber for faults. This method avoids undesirable variations in loss and distance measurements. A launch fiber will help to overcome the blind spot or Dead Zone of an OTDR brought about by high launch power or faults near the launch end of the fiber.

Fluke Networks MMC-62-SCSC Launch Cable is a multimode SC/SC fiber optic cable, is used for high-speed networks installation, inspection and troubleshooting. An OTDR requires launch cables or fiber rings to measure the end-to-end loss of fiber optic links. The multimode fiber has a 62.5/125µm core/cladding diameter.Length is 105 meters.

Fluke Networks MMC-62-SCSC Launch Cable is a multimode SC/SC fiber optic cable, is used for high-speed networks installation, inspection and troubleshooting. An OTDR requires launch cables or fiber rings to measure the end-to-end loss of fiber optic links. The multimode fiber has a 62.5/125µm core/cladding diameter.Length is 105 meters.

Multimode launch cable 50μm SC/SC. Fluke Networks MMC-50-SCSC Launch Cable is a multimode SC/SC fiber optic cable which is used for high-speed networks installation, inspection and troubleshooting. The multimode fiber has a 50/125µm core/cladding diameter. Length is 105 meters.

The DSX-CHA003 coaxial adapters are used in conjunction with the DSX CableAnalyzer to certify coaxial cabling for network and video applications. It supports testing of 50 ohm, 75 ohm, and 93-ohm coaxial cable and its Length-Scaled test limits which automatically adjusts the Insertion Lost limit across the specified frequency range. 

The new digiPHONE+2. A combination of different methods for efficient noise damping enables perfect acoustics that lets you hear only the fault noise.

Greystone - Sensor Type 12 - Pt1000-1000 ohm Platinum RTD. Immersion 100mm (4") c/w ABS utility box -requires thermowell Probe Sensors. The TE200 Series temperature sensors offer a choice of precision platinum RTD's, IC's, or NTC thermistor sensors which can be interfaced with a computerized monitoring or control system.

Fujikura FSM-50S SM MM Fiber Core Alignment Fusion Splicer w/ Cleaver CT-30 50 S

The DSX-PLA004/CHA004 permanent link and channel adapters meet all measurement accuracy specifications for Level IV test equipment. The life of module contacts is >5,000 cycles. Dimensions are 3.0 in x 2.1 in x 1.2 in (75 mm x 54 mm x 30 mm). The permanent link adapter has a 4.85 ft (1.48 m) ±0.25 ft (0.1 m) cable. Weight is ~2.4 oz (68 g) for the channel adapter and ~11.7 oz (332 g) for the permanent link adapter.

The Viavi OMK-36V2 SmartPocket V2 Enterprise Plus Quad Single-Mode & Multi-Mode Test Kit is designed for installing and maintaining singlemode (SM) and multimode (MM) fiber optic networks. The test kit is equipped with the OLP-35V2 optical power meter and the OLS-36V2 quad-wavelength optical light source, which are both dedicated to power level, insertion loss measurements, and continuity checks.

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

The Fujikura 12S incorporates features typically found only in more expensive models. The large 4.5" monitor provides a crystal clear image, even in the brightest sunlight, for evaluating splice quality. The electrode life has been extended to 3,000 splices, minimizing downtime for replacement and stabilization. Software updates are accomplished via the internet allowing users to quickly update their software as new splice programs become available. The fully ruggedized chassis provides for shock, dust and moisture protection while the two camera observation system provides for accurate fiber alignment and loss estimation calculations. The Fujikura 12S is also fully compatible with the FuseConnect line of fusion installable connectors.

Exfo OX1-PRO-I Fiber Explorer: Fast, reliable fiber testing with auto wavelength selection. 10+ hours of use, precise fault detection, and easy-to-read results.

VIEW5 PRO’s 5-inch high-resolution color LCD touch screen with user-friendly intuitive GUI (Graphic User Interface) offers large and clear fiber images to users. By double-tapping the screen, users can Zoom In & Out the image to the world’s highest magnification of 520x. The fusion splicer is equipped with bua ilt-in IoT module that connects to the INNO’s View Pro Cloud Management System for real-time operation and management online. This innovative cloud-based solution is designed to create the most advanced and yet most uncomplicated splicing and work experiences ever.

Product Description

Product Overview

Product Overview

The CFP2-100-Q CertiFiber Pro Quad Optical Loss Test Set (OLTS) helps cabling professionals accomplish more than ever and comes with a Wi-Fi adapter for wireless connectivity to Fluke Networks LinkWare Live software. It's all about accurate, error-free certification, making jobs easier to manage and certifying fiber optic cabling to industry standards, faster.

Viavi OneExpert ONX-580: Advanced DSL & Fiber tester with WiFi, Bluetooth, and 4+ hours battery. Streamline testing with intuitive touch interface and cloud data management.