Search results for: 'disc 2'

The INNO Instrument UN1COLK UN1CO Ladder Mount Work Platform is an ABS workstation designed for secure positioning on ladder rungs during fiber splicing operations. It provides a stable surface for INNO View series fusion splicers and common industry cleavers in elevated or confined environments.

The INNO Instrument IN-SS-45mm fiber splice protection sleeves are heat-shrink sleeves designed to reinforce and protect single fiber fusion splices. Each sleeve uses a composite structure consisting of a cross-linked polyolefin outer tube, hot-melt adhesive inner layer, and stainless steel reinforcing rod.

The INNO Instrument FH Series Ribbon Fiber Holders are detachable accessories designed for use with INNO fusion splicers such as the View4M and View12R. These holders secure and align ribbon fibers during preparation and splicing, supporting configurations from 2-fiber to 12-fiber ribbons with 250µm coatings.

The INNO Instrument SC-SM-UPC-30S is a 10-pack of SC single-mode UPC splice-on connectors designed for 3.0mm jacketed fiber. Using fusion splice termination, these short boot SOC connectors provide stable optical performance without field polishing or index-matching gels.

The INNO Instrument SC-SM-UPC-30 is a 10-pack of SC/UPC single-mode splice-on connectors designed for 3.0mm fiber cables. Each connector is factory pre-cleaved and pre-polished to support consistent optical performance, with typical insertion loss of 0.15 dB and return loss ≥55 dB.

Cisco 2821 Integrated Services Router with WAAS NME-WAE-502-K9 for WAN optimization, onboard Gigabit Ethernet, and WIC-1DSU-T1-V2 T1 CSU/DSU connectivity. Modular design for branch networking versatility.

INNO Instrument OLL-500-652D-SC-UPC OTDR launch fiber reel provides a 500 m singlemode fiber link used with optical time domain reflectometers to stabilize launch conditions and support evaluation of fiber connections during installation, verification, and troubleshooting.

INNO Instrument FL-500-SC-APC is a 500 m singlemode OTDR launch fiber reel with SC/APC connectors designed to support fiber optic link testing. The launch fiber provides a buffer distance that allows Optical Time Domain Reflectometers to measure near-end connections and reflectance with improved visibility.

The INNO Instruments UN1COMK UN1CO Mobile Smart Tray Kit is a portable workstation designed for fiber optic fusion splicing in elevated and field environments. The UN1CO Mobile Kit supports wearable, tripod, ladder, and pole-mounted configurations for field-based fiber installation work.

The INNO Instrument TS Pro Thermal Stripper is designed for removing coating and jacket from optic fibers, supporting single fiber up to 12 ribbon fibers. It accommodates coating diameters from 200 μm to 400 μm and provides selectable heating modes with controlled temperature settings.

The INNO Instrument FL-100-SC-APC Singlemode OTDR Launch Fiber Reel is a 100 m fiber launch cable designed for optical time domain reflectometer testing. It provides a controlled fiber segment that allows OTDR measurements to stabilize before the first connection in a fiber link.

The INNO Instrument SC-SM-APC-30S is a 10-pack of single-mode SC/APC splice-on connectors designed for 3.0mm fiber cables. Featuring a short boot configuration, these pre-cleaved and pre-polished connectors enable fusion-spliced terminations using compatible INNO Instrument fusion splicers.

The INNO Instrument M9+ is a compact core alignment fusion splicer for single fiber SM, MM, DS, and NZDS applications. It features ultrafast splice and heating cycles, a 4.3-inch full touch LCD, automatic arc calibration, and integrated heater in a field-ready kit.

Single Fluke DTX-MFM2 multimode fiber module for 850/1300 nm dual-fiber loss and length testing. Supports SC output, interchangeable adapters, VFL, and FindFiber functions.

The INNO Instrument IN-SS-40mm fiber splice protection sleeve is a 40 mm heat-shrink sleeve designed to reinforce single-fiber fusion splices. A stainless steel strength member helps prevent bending while the clear outer tube allows inspection of the splice during installation.

The INNO Instrument IN-RS-40mm ribbon fiber splice protection sleeve is a 40 mm heat-shrink sleeve designed to protect ribbon fiber fusion splices. The sleeve incorporates a single ceramic reinforcement rod for structural support and alignment protection after splicing. A clear heat-shrinkable outer tube combined with an internal EVA adhesive liner.

The INNO Instrument OLL-1000-652D-SC-UPC OTDR Launch Fiber Reel provides a 1000 meter G.652D singlemode fiber lead designed for OTDR testing. Featuring SC-UPC connectors, the launch fiber enables accurate measurement of near-end and far-end events.

INNO Instrument OLL-500-652D-SC-APC OTDR launch fiber cable provides a 500 m singlemode buffer between an OTDR and the fiber under test. Using G.652D 9/125 µm fiber with SC/APC connectors on both ends, it supports near-end connector characterization and reveal events that may be obscured during OTDR trace acquisition.

The INNO Instrument FL-300-SC-APC is a 300 m Singlemode launch fiber reel designed for Optical Time Domain Reflectometer (OTDR) testing. It provides a controlled fiber length between the OTDR and the link under test, enabling measurement of the first connector in a fiber span. The reel format protects the fiber during storage and field deployment.

The INNO Instrument FL-100-SC-UPC is a 100 m singlemode OTDR launch fiber reel designed for fiber optic testing and link characterization. Featuring SC/UPC connectors on both ends, this launch cable acts as a pulse suppressor and delay line that enables Optical Time-Domain Reflectometers (OTDR) to measure insertion loss.

The INNO Instrument View 600 OTDR is a modular fiber optic test platform configured with a 1310/1550 nm single-mode OTDR module delivering 36/35 dB dynamic range. This kit includes the V-20 fiber inspection microscope for connector end-face inspection. The View 600 integrates automated SOLA link analysis, optical power meter functionality.

The INNO Instrument IN-SS-60mm fiber splice protection sleeves provide mechanical reinforcement for fusion-spliced optical fibers. Each 60 mm sleeve uses a clear heat-shrink polyolefin outer tube, internal adhesive liner, and stainless steel strength member to support fiber alignment after the splicing process.

The INNO Instrument IN-RD-40mm ribbon fiber protection sleeve provides environmental and mechanical protection for ribbon fiber fusion splices. The 40 mm heat-shrink sleeve incorporates a double ceramic rod structure that maintains alignment and rigidity during the shrinking process.

The INNO Instrument OLL-1000-652D-SC-APC is a 1000 m single-mode OTDR launch fiber reel designed for dead-zone elimination in fiber optic testing. The assembly uses G.652D single-mode fiber and SC/APC connectors to support accurate reflectance and insertion-loss measurement when testing optical links with an OTDR.

The INNO Instrument 300-meter Fiber Optic Launch Reel is a  singlemode reference fiber used with optical time domain reflectometers (OTDR) to eliminate near-end dead zones during fiber testing. The reel integrates singlemode fiber with SC/UPC connectors on both ends that enables accurate measurement of connector loss and reflectance.