Search results for: 'after with'

Detects IntelliTone digital signal for Locate, Isolate and CableMap Detects Analog SmartTonne Signal (500-1200Hz) and other analog toners.

OptiTap Simplex Plug AdapterFMAE Series adapters are used for patch cord inspection. They attach to the Patch Cord Microscope on theSmartClass Fiber Series, as well as the Fva Benchtop Microscope. They can also be connected to any VIAVI probe microscope by using the BFP-UFMAE, together with an FBP-BAP1 adapter. FMAE Series adapters are all female threaded.

Cast patch cord RJ45-RJ45 CAT category 6. It is made of a red U/UTP cable in a LSZH shell. Designed for switching network equipment.

The DSX-CHA003 coaxial adapters are used in conjunction with the DSX CableAnalyzer to certify coaxial cabling for network and video applications. It supports testing of 50 ohm, 75 ohm, and 93-ohm coaxial cable and its Length-Scaled test limits which automatically adjusts the Insertion Lost limit across the specified frequency range. 

The new digiPHONE+2. A combination of different methods for efficient noise damping enables perfect acoustics that lets you hear only the fault noise.

Greystone - Sensor Type 12 - Pt1000-1000 ohm Platinum RTD. Immersion 100mm (4") c/w ABS utility box -requires thermowell Probe Sensors. The TE200 Series temperature sensors offer a choice of precision platinum RTD's, IC's, or NTC thermistor sensors which can be interfaced with a computerized monitoring or control system.

Fluke Networks MMC-62-SCSC Launch Cable is a multimode SC/SC fiber optic cable, is used for high-speed networks installation, inspection and troubleshooting. An OTDR requires launch cables or fiber rings to measure the end-to-end loss of fiber optic links. The multimode fiber has a 62.5/125µm core/cladding diameter.Length is 105 meters.

Fluke Networks MMC-62-SCSC Launch Cable is a multimode SC/SC fiber optic cable, is used for high-speed networks installation, inspection and troubleshooting. An OTDR requires launch cables or fiber rings to measure the end-to-end loss of fiber optic links. The multimode fiber has a 62.5/125µm core/cladding diameter.Length is 105 meters.

Multimode launch cable 50μm SC/SC. Fluke Networks MMC-50-SCSC Launch Cable is a multimode SC/SC fiber optic cable which is used for high-speed networks installation, inspection and troubleshooting. The multimode fiber has a 50/125µm core/cladding diameter. Length is 105 meters.

Fujikura FSM-50S SM MM Fiber Core Alignment Fusion Splicer w/ Cleaver CT-30 50 S

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

The DTX-MFM2 fiber module are used with a DTX Series Cable Analyzer to test and certify fiber optic cabling installations. 

The DSX-PLA004/CHA004 permanent link and channel adapters meet all measurement accuracy specifications for Level IV test equipment. The life of module contacts is >5,000 cycles. Dimensions are 3.0 in x 2.1 in x 1.2 in (75 mm x 54 mm x 30 mm). The permanent link adapter has a 4.85 ft (1.48 m) ±0.25 ft (0.1 m) cable. Weight is ~2.4 oz (68 g) for the channel adapter and ~11.7 oz (332 g) for the permanent link adapter.

VIEW5 PRO’s 5-inch high-resolution color LCD touch screen with user-friendly intuitive GUI (Graphic User Interface) offers large and clear fiber images to users. By double-tapping the screen, users can Zoom In & Out the image to the world’s highest magnification of 520x. The fusion splicer is equipped with bua ilt-in IoT module that connects to the INNO’s View Pro Cloud Management System for real-time operation and management online. This innovative cloud-based solution is designed to create the most advanced and yet most uncomplicated splicing and work experiences ever.

Product Overview

The CFP2-100-Q CertiFiber Pro Quad Optical Loss Test Set (OLTS) helps cabling professionals accomplish more than ever and comes with a Wi-Fi adapter for wireless connectivity to Fluke Networks LinkWare Live software. It's all about accurate, error-free certification, making jobs easier to manage and certifying fiber optic cabling to industry standards, faster.

Product Overview