Search results for: 'carrier'

Launch Box

Launch Box

Launch Box

OptiTap Simplex Plug AdapterFMAE Series adapters are used for patch cord inspection. They attach to the Patch Cord Microscope on theSmartClass Fiber Series, as well as the Fva Benchtop Microscope. They can also be connected to any VIAVI probe microscope by using the BFP-UFMAE, together with an FBP-BAP1 adapter. FMAE Series adapters are all female threaded.

An OTDR launch cable, which connects the OTDR to the link-under-test, discloses the insertion loss and reflectance of the near-end connection. It is often available on a small spool or within a “launch box”, which is used to create the proper conditions for testing another similar optical fiber for faults. This method avoids undesirable variations in loss and distance measurements. A launch fiber will help to overcome the blind spot or Dead Zone of an OTDR brought about by high launch power or faults near the launch end of the fiber.

Cast patch cord RJ45-RJ45 CAT category 6. It is made of a red U/UTP cable in a LSZH shell. Designed for switching network equipment.

Fluke Networks MMC-62-SCSC Launch Cable is a multimode SC/SC fiber optic cable, is used for high-speed networks installation, inspection and troubleshooting. An OTDR requires launch cables or fiber rings to measure the end-to-end loss of fiber optic links. The multimode fiber has a 62.5/125µm core/cladding diameter.Length is 105 meters.

The DSX-CHA003 coaxial adapters are used in conjunction with the DSX CableAnalyzer to certify coaxial cabling for network and video applications. It supports testing of 50 ohm, 75 ohm, and 93-ohm coaxial cable and its Length-Scaled test limits which automatically adjusts the Insertion Lost limit across the specified frequency range. 

The new digiPHONE+2. A combination of different methods for efficient noise damping enables perfect acoustics that lets you hear only the fault noise.

Fluke Networks MMC-62-SCSC Launch Cable is a multimode SC/SC fiber optic cable, is used for high-speed networks installation, inspection and troubleshooting. An OTDR requires launch cables or fiber rings to measure the end-to-end loss of fiber optic links. The multimode fiber has a 62.5/125µm core/cladding diameter.Length is 105 meters.

Multimode launch cable 50μm SC/SC. Fluke Networks MMC-50-SCSC Launch Cable is a multimode SC/SC fiber optic cable which is used for high-speed networks installation, inspection and troubleshooting. The multimode fiber has a 50/125µm core/cladding diameter. Length is 105 meters.

Greystone - Sensor Type 12 - Pt1000-1000 ohm Platinum RTD. Immersion 100mm (4") c/w ABS utility box -requires thermowell Probe Sensors. The TE200 Series temperature sensors offer a choice of precision platinum RTD's, IC's, or NTC thermistor sensors which can be interfaced with a computerized monitoring or control system.

Fujikura FSM-50S SM MM Fiber Core Alignment Fusion Splicer w/ Cleaver CT-30 50 S

The Fujikura 12S incorporates features typically found only in more expensive models. The large 4.5" monitor provides a crystal clear image, even in the brightest sunlight, for evaluating splice quality. The electrode life has been extended to 3,000 splices, minimizing downtime for replacement and stabilization. Software updates are accomplished via the internet allowing users to quickly update their software as new splice programs become available. The fully ruggedized chassis provides for shock, dust and moisture protection while the two camera observation system provides for accurate fiber alignment and loss estimation calculations. The Fujikura 12S is also fully compatible with the FuseConnect line of fusion installable connectors.

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

The DSX-PLA004/CHA004 permanent link and channel adapters meet all measurement accuracy specifications for Level IV test equipment. The life of module contacts is >5,000 cycles. Dimensions are 3.0 in x 2.1 in x 1.2 in (75 mm x 54 mm x 30 mm). The permanent link adapter has a 4.85 ft (1.48 m) ±0.25 ft (0.1 m) cable. Weight is ~2.4 oz (68 g) for the channel adapter and ~11.7 oz (332 g) for the permanent link adapter.

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

The DTX-MFM2 fiber module are used with a DTX Series Cable Analyzer to test and certify fiber optic cabling installations. 

The Viavi OLS-36V2 (2334/21) SmartPocket V2 Optical Light Source is a durable and compact device used for performing insertion loss measurement and continuity checks in the field. It is designed to be user-friendly and convenient, allowing for easy and quick testing of both single mode and multimode optical fiber networks. This device is best used in conjunction with the OLP-3xV2 optical power meters, which are sold separately. The SmartPocket V2 source is equipped with Auto-λ and Multi-λ functions that work with any SmartPocket V2 power meter, allowing for a cost-effective solution for testing and troubleshooting optical fibers in the field. Its one-button operation ensures a fast, straightforward, and mistake-free testing solution, making the SmartPocket OLS-36V2 the perfect tool for daily field testing.

Product Description

Product Overview

Product Overview