Search results for: 'Requirements'

The Fluke Networks LinkIQ LIQ-KIT-FQM-100MIC verifies 10G cable performance, tests switches and PoE, traces copper and fiber faults, and provides end-to-end network troubleshooting.

Fluke Networks DSX2-8000-ADD-R kit expands DSX-8000 systems with Versiv 2 Remote, Cat 8 adapters, and accessories for complete copper certification.

Clark Wire SMPTE Fiber Camera Cable: 250' bend-insensitive, extra-flexible, high-performance cable for remote, ENG, and studio use. Built for durability and reliability.

Fluke Cable Analyzer DSX2-8000QI/GLD – High-performance cable certifier for copper and fiber, supporting Cat 8 up to 2000 MHz with Level 2G accuracy. Streamlines Tier-1 & Tier-2 certification with fast testing, diagnostics, and LinkWare™ Live reporting.

ABB C99-94501 delivers a high-temp fiber optic cable assembly for reliable FlameScanner monitoring, ensuring clear optical performance for industrial burner systems.

Allen-Bradley PN-94201 is an industrial fiber optic cable designed for reliable optical signal transmission in automation environments where electrical noise immunity and stable communication are required.

Allen-Bradley 43GR-TIS10SS is a 36-inch bifurcated glass fiber optic cable for diffuse sensing applications. It features a stainless steel flexible conduit, right-angle M6 threaded tip, and is designed for use with small-aperture photoelectric sensors in industrial environments.

The INNO Instrument E-50 Electrodes are replacement consumables designed for use with compatible INNO fusion splicers. Supplied as a matched pair, they generate the controlled electrical arc required for fiber fusion. The E-50 set supports routine maintenance and consistent splicing performance within fiber optic installation and service workflows.

FTTH Innovations FIG air blown microfibre installation tool with electronic push force control and cruise control mode for controlled fibre installation in microduct at speeds up to 100 m/min.

Fluke Networks MMC-50-SCST multimode launch cable with 50 µm fiber and SC/ST connectors. Designed for fiber optic testing applications, this 140-meter launch cable supports network test setups requiring multimode fiber connections.

Fluke Networks FINDFIBER FindFiber Remote ID Source enables fast optical fiber identification when used with a SimpliFiber Pro power meter, allowing single-technician verification of fiber routing and polarity.

Fluke Networks FI1000-MPO-RT replacement tip for FI-1000 FiberInspector provides precise MPO/MTP fiber inspection without a translator knob for seamless testing.

Fluke SM 9UM launch cord ensures accurate OTDR testing with single-mode SC/APC connectors, delivering reliable fiber optic network measurements.

The INNO Instrument HTS-SOC-01 is a heater cover accessory designed for use with compatible INNO fusion splicers. It replaces the standard heater cover to support splice-on connector (SOC) termination workflows where connector geometry requires an alternate heater configuration.

Fluke Networks FI-500CP — Replacement camera probe for the FI-500 FiberInspector Micro, delivering 200× magnification, a 5 megapixel sensor, autofocus and auto-center, and PortBright™ built-in illumination to inspect fiber end-faces in tight, low-light panels.

Fluke Networks fiber optic cable: dependable singlemode SC/SC 2m cord ensuring stable, high-speed network connectivity for precise testing.

Single Fluke DTX-MFM2 multimode fiber module for 850/1300 nm dual-fiber loss and length testing. Supports SC output, interchangeable adapters, VFL, and FindFiber functions.

Fluke Networks SMC-9-SCST launch cable delivers 160m singlemode fiber for accurate OTDR testing, stable network connectivity, and compatibility with OptiFiber units.

Fluke Networks fiber optic launch cable delivers reliable 62.5 µm multimode performance with 105m length, SC to LC connectors, ideal for network testing.