Search results for: 'used 20'

The INNO Instrument EG-18 Electrode Grinder is a portable maintenance tool designed to resurface tungsten electrode rods used in fiber optic fusion splicers. It restores electrode tip geometry to support stable arc discharge and consistent splicing performance in field and lab environments.

INNO Instrument OLL-500-652D-SC-UPC OTDR launch fiber reel provides a 500 m singlemode fiber link used with optical time domain reflectometers to stabilize launch conditions and support evaluation of fiber connections during installation, verification, and troubleshooting.

The INNO Instrument FL-300-SC-APC is a 300 m Singlemode launch fiber reel designed for Optical Time Domain Reflectometer (OTDR) testing. It provides a controlled fiber length between the OTDR and the link under test, enabling measurement of the first connector in a fiber span. The reel format protects the fiber during storage and field deployment.

Single Fluke DTX-MFM2 multimode fiber module for 850/1300 nm dual-fiber loss and length testing. Supports SC output, interchangeable adapters, VFL, and FindFiber functions.

The INNO Instrument OLL-1000-652D-SC-APC is a 1000 m single-mode OTDR launch fiber reel designed for dead-zone elimination in fiber optic testing. The assembly uses G.652D single-mode fiber and SC/APC connectors to support accurate reflectance and insertion-loss measurement when testing optical links with an OTDR.

The INNO Instrument 300-meter Fiber Optic Launch Reel is a  singlemode reference fiber used with optical time domain reflectometers (OTDR) to eliminate near-end dead zones during fiber testing. The reel integrates singlemode fiber with SC/UPC connectors on both ends that enables accurate measurement of connector loss and reflectance.

Sumitomo Type-39 FCM (Micro Core / FastCat) is a core-alignment optical fiber fusion splicer for single-fiber joining work. Uses Direct Core Monitoring (HDCM) loss estimation and dual independent heat-shrink ovens to support splice-and-sleeve workflows in field or bench splicing environments.

The EXFO MaxTester 730C is a handheld singlemode OTDR configured for 1310 and 1550 nm fiber testing. This unit includes an installed PM-MAX-2X power meter hardware module and RF capability with Wi-Fi and Bluetooth for combined OTDR and power measurement.

The INNO Instrument E-50 Electrodes are replacement consumables designed for use with compatible INNO fusion splicers. Supplied as a matched pair, they generate the controlled electrical arc required for fiber fusion. The E-50 set supports routine maintenance and consistent splicing performance within fiber optic installation and service workflows.

The INNO Instrument CH-01 Universal Fiber Holder is a cleaver accessory designed to secure multiple fiber cable types during the cleaving process. It supports 250µm and 900µm fiber, flat or drop cable enabling technicians to work across common installation formats without changing holders. Compatible with select INNO high-precision cleavers.

The INNO Instrument CG-24 Cooling Tray is a standard accessory designed for the INNO Instrument A3 Fusion Splicer. It provides a dedicated, heat-resistant surface for fiber optic protection sleeves immediately after oven heating.

The INNO Instrument UN1COLK UN1CO Ladder Mount Work Platform is an ABS workstation designed for secure positioning on ladder rungs during fiber splicing operations. It provides a stable surface for INNO View series fusion splicers and common industry cleavers in elevated or confined environments.

The INNO Instrument FL-100-SC-UPC is a 100 m singlemode OTDR launch fiber reel designed for fiber optic testing and link characterization. Featuring SC/UPC connectors on both ends, this launch cable acts as a pulse suppressor and delay line that enables Optical Time-Domain Reflectometers (OTDR) to measure insertion loss.

The INNO Instrument IN-RS-40mm ribbon fiber splice protection sleeve is a 40 mm heat-shrink sleeve designed to protect ribbon fiber fusion splices. The sleeve incorporates a single ceramic reinforcement rod for structural support and alignment protection after splicing. A clear heat-shrinkable outer tube combined with an internal EVA adhesive liner.

The INNO Instrument FL-100-SC-APC Singlemode OTDR Launch Fiber Reel is a 100 m fiber launch cable designed for optical time domain reflectometer testing. It provides a controlled fiber segment that allows OTDR measurements to stabilize before the first connection in a fiber link.

The INNO Instrument SC-SM-UPC-09 is a 10-pack of single-mode SC/UPC splice-on connectors for 900µm fiber. Designed for fusion splicer termination, these connectors eliminate polishing, adhesives, and mechanical splicing. With typical ≤0.2 dB insertion loss and ≥55 dB return loss, they support G.652D and G.657A2 fiber types.

Viavi T-BERD 2000 DWDM: Advanced fiber testing solution with built-in power meter, VFL, and 9-hour battery. Boost productivity with smart, fast, and reliable field testing.

The INNO Instrument IN-SS-60mm fiber splice protection sleeves provide mechanical reinforcement for fusion-spliced optical fibers. Each 60 mm sleeve uses a clear heat-shrink polyolefin outer tube, internal adhesive liner, and stainless steel strength member to support fiber alignment after the splicing process.

The INNO Instrument  Universal Fiber Holder is an accessory designed for INNO fusion splicers to position and secure optical fibers during splicing. The holder supports multiple fiber preparation types and provides stable alignment inside the splicer. Variant options support different splicer models and left or right holder configurations.

The INNO Instrument Ribbon Holder are fiber ribbon holders designed for use with INNO Instrument View12R and View12R PRO fusion splicers. The holder supports 250 µm ribbon fiber during the splicing process, maintaining fiber alignment and stability within the splicer. Its detachable design allows quick installation and removal when preparing ribbon fibers for fusion splicing.

The INNO Instrument FH Series Universal Fiber Holder is an accessory designed for INNO fusion splicers to position and secure optical fibers during splicing. The holder supports multiple fiber preparation types and provides stable alignment inside the splicer. Variant options support different splicer models and left or right holder configurations.

Upgrade your fiber optic projects with this used INNO M9+ fusion splicer kit, featuring a standard V1 fiber cleaver and a low splice count for dependable performance. Don’t miss out—order from Cartoli now for quality and value!