Search results for: 'allowing'

Fluke Networks LEAD-ALIG-100 Test Lead features braided durability, insulated alligator clips, and BNC connection for TS100 series testing.

Fluke TL960 test leads with micro-hooks for precise component connections, 90 cm PVC insulation, 4 mm banana plugs, safe for low-voltage applications.

Fluke industrial test lead set includes SureGrip clips, test probes, temperature probe, and soft case for accurate, safe electrical measurements.

The Eagle Eye IBEX-Temperature Probe-IR is a temperature probe accessory designed for use with IBEX battery testing equipment. The probe connects via cable and supports temperature measurement during battery testing and diagnostic procedures.

Eagle Eye IBEX-Extended Arm Rod Set is a 30 in. LED-lit test lead extender designed for use with IBEX-Series testers to reach battery terminals in difficult locations.

The Fluke TP88 Rigid Back Probe Pin Set includes two fine-tip, rigid back probe pins designed for use with 2 mm test probes. The red and black insulated pins slide onto compatible probes and allow access between weather pack seals and wires. Tested to 60 V DC.

Pomona 5697-60 antenna cable delivers reliable 50 ohm BNC connectivity with gold-plated contacts and high-quality construction in a non-booted design.

Pomona 6275 precision test lead set features miniature probes, stainless steel tips, flexible silicone leads, and enhanced safety for dense circuit testing.

Fluke Networks P3218028 line cord with angled piercing pin clips enables testing of insulated telephone wires with compatible TS series test sets.

Fluke TLK290 probe set: Flexible sockets and alligator clip for safe, precise testing of motors, 3-phase plugs, and 4–8 mm connections.

Flexible Rogowski AC current sensor with 120" coil length. Dual range 300/3000A AC with 100mV/A and 10mV/A output. Ideal for large bus bars and cable bundles. Compatible with DMMs, loggers, and power meters.

Bussmann LPJ-15SP time-delay fuse delivers 15A circuit protection with dual-element response and current-limiting performance for industrial electrical systems up to 600VAC.

Fluke L210 Probe Light Kit provides bright LED illumination and probe extenders to improve visibility and safety when testing live electrical circuits.

Fluke AC175 alligator clip set offers insulated, threaded-shaft clips with 7 mm jaw opening for secure probe connections and flexible field use.

Fluke Networks FI1000-MPO-UTIP probe tip enables precise MPO/MTP UPC fiber inspection on FI-1000 probes, ideal for patch cord and bulkhead connector analysis.

Fluke 700TC2 plug kit: seven thermocouple mini-connectors for J, K, T, E, R/S types. Reliable connections for process calibration setups.

AEMC 2118.53 Fuse Set 0.5A 250V Slow Blow: Includes 5 fuses, 5x20mm size, designed for precise circuit protection in DTR 8500 & 8510 instruments.

Snap On MT2500-43 Short Test Lead Jumper: Essential tool for reliable diagnostics. Designed for precision and durability to enhance your testing efficiency.

Pomona 1270 adapter converts double banana jack instruments to BNC with shielded, tarnish-resistant contacts and stacking banana plug versatility.

Fluke Networks P3080009 line cord provides angled bed-of-nails and piercing pin clips for TS30 and TS120 test sets, enabling safe, durable insulated wire testing.

Fluke TL71 test lead set with silicone-insulated, right-angle probes for precise µV measurements. CAT IV 600V, CAT III 1000V rated for safe, reliable testing.

Fluke Networks FI1000-SCAPC-TIP probe tip enables precise SC/APC bulkhead inspection with FI-1000 and OptiFiber Pro, ensuring accurate fiber connector evaluation.

Fluke Networks LEAD-ABN-PPIN test leads feature durable braided cables, angled bed-of-nails, and piercing pin clips for reliable telecom testing.

AEMC ALS-1 AC Line Splitter: Boost clamp meter sensitivity with X1 and X10 clamp positions plus voltage checking for safe, accurate current measurement.