Search results for: 'require'

AEMC 2118.70 Kelvin Clips provide 20 ft color-coded 10A Hippo test leads with spade lug terminations for compatible micro-ohmmeter connections.

Eagle Eye IBEX 4-Point Test Leads for battery analyzers provide four-contact measurement for battery resistance and voltage testing with compatible IBEX systems.

The Harold Beck & Sons 11-1373-01 is a 7 Amp fast-acting fuse used for overcurrent protection in Digital Control Module (DCM) circuits. Designed for use within Beck electric actuator systems, this listing includes a quantity of five identical fuses.

Fluke T5-RLS test leads: reliable replacements for T5-600 and T5-1000 testers, delivering accurate connections and lasting durability.

Fluke Networks MPO Adapter: Reliable Type A fiber optic connection for SM APC networks, compact 5-inch design, and easy installation.

AEMC 2129.95 RTD Temperature Probe provides temperature compensation capability for AEMC 6250 and 6255 testing systems, helping improve measurement accuracy during resistance testing where ambient temperature variations affect results.

Littelfuse JTD-030ID fuses deliver 30A Class J circuit protection with indicating status visibility, 600 VAC or less rating, and time-delay performance for compatible electrical systems.

The Eagle Eye IBEX-Temperature Probe-IR is a temperature probe accessory designed for use with IBEX battery testing equipment. The probe connects via cable and supports temperature measurement during battery testing and diagnostic procedures.

Fluke TP2 Slim-Reach test probe set includes one red and one black probe with 2 mm diameter stainless steel tips. Designed for probing closely spaced or recessed terminals, the probes are rated for 10 A and suitable for CAT III 1000 V and CAT IV 600 V environments.

The Fluke TP88 Rigid Back Probe Pin Set includes two fine-tip, rigid back probe pins designed for use with 2 mm test probes. The red and black insulated pins slide onto compatible probes and allow access between weather pack seals and wires. Tested to 60 V DC.

Pomona 5697-60 antenna cable delivers reliable 50 ohm BNC connectivity with gold-plated contacts and high-quality construction in a non-booted design.

Fluke Networks P3218028 line cord with angled piercing pin clips enables testing of insulated telephone wires with compatible TS series test sets.

Fluke FUSE-11A/1000V B5 replacement fuses provide 11A, 1000V protection for Fluke digital multimeters, ensuring safe, reliable overcurrent protection.

Fluke Networks SRC-9-FCFC fiber cord ensures reliable singlemode testing of FC terminated fibers, delivering accurate network performance verification.

Fluke Networks USB Interface Cable ensures fast, reliable data transfer between USB-A and Micro-B devices with durable copper conductors.

Rohde & Schwarz FSH-Z1 true RMS terminating RF power sensor for 10 MHz–8 GHz measurements, providing accurate average power analysis and direct compatibility with FSH series handheld spectrum analyzers.

AEMC 2151.31 delivers a crisp 1 ft blue 5kV jumper lead replacement for AEMC Megohmmeter Models 5050, 5060, 5070, and 6505 with exact-fit high-voltage test lead connectivity.

AEMC 2136.77 Replacement Lead Set provides 15 ft test leads designed for use with AEMC DTR Models 8500 and 8510. Supplied as a set of two leads and intended as a replacement for Cat #2118.48.

Fluke TL224 SureGrip insulated test leads include one red and one black lead with safety-shrouded standard diameter banana plugs. The leads feature a right-angle connector on one end and a straight connector on the other, reinforced strain relief, and silicone-insulated wire designed to resist heat and cold.

The Fluke TL75 Hard Point Test Lead Set combines test lead and probe into a single unit for general-purpose electrical measurements. This set includes one red and one black PVC-insulated lead, each 48 inches long, with right-angle shrouded banana plugs and removable protective caps.

Pomona 6733-0 bare wire control cable features flexible silicone insulation, high strand copper conductor, and CAT III–compliant performance when properly terminated.

Fluke Networks P3218024 line cord enables reliable testing of insulated telephone wires using straight bed-of-nails clips with compatible lineman test sets.

Fluke 80CK-M Type K mini-connectors offer reliable thermocouple wire termination with isothermal screw terminals, ideal for Fluke 80TK and Fluke 50 Series tools.

AEMC 2154.76 Fuse Set of 3, 0.63A, 1000V fast blow fuses designed for Models 5212, 5215, and 5217, ensuring reliable circuit protection.