Search results for: 'it's an'

The SATO RH1731100 is a genuine SEN 5 Cable data transfer cable assembly used inside SATO industrial label printers. This internal electrical component includes an attached micro switch and is designed to connect internal printer mechanisms to the main circuitry in supported M84xxS and M84xxSe series printers.

The Thermo Environmental 2200-0-010 Heater Control Module (P/N 22000010) is an industrial control board designed for regulated heater management within environmental and analytical systems. This module functions as a temperature control component in Thermo Environmental instrumentation platforms.

The Telemotive E7207-1 Circuit Board is an industrial automation component used in Telemotive radio control systems. Identified by part number E7207-1, this board is commonly applied in industrial control environments including crane and hoist remote control systems.

Siemens A1-108-101-502 operator display control panel for parameter access, status monitoring, and fault diagnostics in compatible SIMOREG DC drive systems.

The Deltron ST150-1XX is a 150 W industrial AC-DC switching power supply with three DC outputs. It provides one 5 V output rated at 20 A and two 12 V outputs rated at 5 A each. Designed for terminal block wiring, it supports dual-range AC input and is used in control and automation systems.

The Telemecanique XSAV32373 is an inductive proximity sensor designed for rotation monitoring applications. It features a cylindrical M30 nickel plated brass housing, 10 mm nominal sensing distance, PNP output with 1 NC function, and operates on 12 to 48 V DC. The sensor includes a fixed 2 meter cable connection and is rated IP67.

ZORO Select model 6UEE7 is an electric sequencer designed for HVAC and refrigeration systems. It operates on 24V AC control voltage and features two switches with adjustable on and off timing. Rated for up to 25A resistive load, it supports horizontal or vertical installation.

The Siemens TA2J6500 is an aluminum body 2-barrel lug accessory for use with 2- or 3-pole 200A–400A JD and LD frame molded case circuit breakers. It supports copper conductors from 3/0 AWG to 500 kcmil and aluminum conductors from 4/0 AWG to 500 kcmil, and is suitable for both line and load side connections.

The Leviton 2453 is a 20 Amp, 277/480 Volt AC locking connector with a NEMA L19-20R configuration. It features a 4-pole, 4-wire, non-grounding design for 3-phase WYE applications. The connector uses an impact-modified nylon body with solid brass blades and contacts.

The Curtis Industries CUS8 is an 8-pin octal relay socket base designed for industrial control applications. Rated at 10A and up to 300V, it provides a standardized receptacle for compatible 2PDT octal relays or timers and supports secure screw-terminal wiring.

The FANUC A06B-6114-K213/E is an industrial connector plug used for encoder or brake connections on FANUC servo motors. Manufactured for CNC and automation systems, this connector is supplied as a right-angle style plug and is identified by the FANUC part number A06B-6114-K213/E.

The Mitsubishi CP30-BA 1-Pole 7A M-Curve Circuit Protector is a compact hydraulic-magnetic circuit protector designed for supplementary protection of low-capacity industrial control circuits. It supports AC 250 V and DC 65 V operation and uses an M-curve trip characteristic suitable for moderate inrush loads.

The Advance L-220-F is a magnetic reactor ballast designed to operate two 15W or 20W preheat fluorescent lamps at 120V AC, 60 Hz. It regulates lamp current using an inductive core and requires external starters for lamp ignition in preheat fluorescent systems.

The Contrex M-Drive 4E is a digital DC motor drive and motion controller designed for closed-loop speed regulation of permanent magnet DC motors up to 2 HP. It supports dual AC input voltage, selectable DC output, serial communication, and integrated operator interface.

Hubbell HC69476733 industrial resistor assembly delivers controlled resistive load handling for power dissipation and current regulation in industrial electrical systems.

The General Electric DS200DDTBG2ABB is an LCI Auxiliary I/O Terminal Board for GE Mark V Speedtronic gas and steam turbine control systems. It provides auxiliary signal termination, conditioning, and isolation for analog and digital I/O in high-voltage industrial control environments.

General Electric CR2790E100A2 general purpose control relay with 115V AC 60Hz coil, 10A contact rating, and 300V max rating for industrial control and switching applications.

The Fireye 4-314-1 is an ultraviolet sensing tube used in Fireye flame scanner assemblies. This tube is supplied as a standalone replacement component and is identified on the original manufacturer carton for use with select 45UV series scanners. No scanner body or accessories are included.

Eaton DILEM-10 XTMC9A10B XT IEC mini contactor delivers 3-pole full-voltage non-reversing control with an 8.80A rating, 20A continuous rating, 220–240 Vac coil, 1 NO contact configuration, and screw terminals.

The ATC TDH-120-ALA-100 is a delayed interval time delay relay designed for industrial control applications. It operates on 120 VAC/DC supply voltage and provides an adjustable delay range from 1 to 100 seconds using dual front-mounted dials. The relay features a plug-in octal base and relay contacts rated at 10A.

Eaton XTCE012B10TD contactor delivers reliable 3-pole motor control with a 24V DC coil, 12A rating, and IEC compatibility for XT series motor starter systems.

Allen-Bradley 1492-FB3C30-L is a 3-pole Class CC fuse holder for the 1492 Wiring System, rated 30A and up to 600V AC, featuring an integrated LED indicator for clear fuse status visibility.

Moxa PWR-G7000-AC power supply module with 85–264 VAC input for ICS-G7000 series switches, supporting 47–63 Hz and 0–60°C operation in modular chassis.

Schneider Electric RPM21BD relay offers reliable 24V DC DPDT switching for RPM-series control systems, with diode protection and compact plug-in design.