Search results for: 'the the'

The AEG SH 05.31 is a 4-pole auxiliary contactor from the SH 05 series with a 24V DC coil. It features a 3NO + 1NC contact configuration (31E) and screw terminals. Rated per AC-15 and DC-13 utilization categories as specified in the AEG 2014 extract catalogue.

The REXA Koso S96111 Pulse Mod I/O Interface PCB Board is an internal electronic module used in REXA Electraulic™ actuators. It supports pulse modulation control and manages input and output signals within the actuator’s control system for precise positioning and communication.

Emerson Ovation 1C31219G01 Relay Output Electronics Module for interfacing between the Ovation controller and mechanical relays in a relay output assembly.

Allen-Bradley 1734-MB 95723404 Series A mounting base delivers secure DIN-rail installation for POINT I/O modules, with keying and POINTBus connections for reliable setup.

Allen-Bradley 100-DS1-20 auxiliary contact block expands control contacts on 100-D contactors, delivering status signaling for industrial motor control.

The Eaton P1-25/V/SVB is a 25 A, three-pole main switch from the Eaton Moeller® P1 series designed for rear mounting applications. It features a door-coupling rotary drive with a red rotary handle and yellow locking ring, and supports emergency switching off functionality. The switch is rated up to 690 V AC, provides IP65 front protection, and is lockable in the 0 (Off) position for secured isolation.

The SATO RH1731100 is a genuine SEN 5 Cable data transfer cable assembly used inside SATO industrial label printers. This internal electrical component includes an attached micro switch and is designed to connect internal printer mechanisms to the main circuitry in supported M84xxS and M84xxSe series printers.

The C3 Controls DDS2-340-DHGRY is a non-fused, 40 amp, 3-pole disconnect switch designed for door-mount applications. It features a red/yellow rotary operating handle and an IP65 ingress protection rating for use in industrial control environments requiring reliable circuit isolation.

Black Box IC107A-R2 RS-232↔RS-422/485 converter for data-only serial communication. Supports 4-wire full-duplex operation for point-to-point or multipoint links. Provides a DB25 female RS-232 interface and a 4-pin terminal block for RS-422/485 with TX/RX/PWR LEDs.

The Fluke CV400 is a 4 in (95 mm) infrared window with hand turn door latch for electrical panel inspection. It features a ClirVu coating system, AutoGround functionality, IP67 rating, and a 63 kA arc-blast rating tested at KEMA. Designed for quick installation without removing the panel door.

The IDEC APW299D-W-120V is a panel-mount white pilot light indicator designed for industrial control applications. This unit operates on 120V AC and features a dome-style white lens with a metallic bezel. It is UL listed and CSA marked, with screw terminal connections housed in a compact rectangular base.

Yamatake Honeywell 8240-7444-001 ENH Relay Terminal Panel. This panel provides relay termination using multiple installed plug-in relays and numbered screw terminals on a single PCB assembly. Identified by manufacturer silkscreen and assembly number only.

The Emerson Fisher-Rosemount KJ4001X1-CA1 is an I/O terminal block used as an interface between field wiring and control system I/O modules. The unit provides 16 numbered terminal positions and is designed for industrial automation installations, including hazardous location environments as indicated on the device label.

The Siemens Sentron ED43B020 is a 3-pole, 20 amp molded case circuit breaker rated for 480 VAC operation. It provides thermal-magnetic protection with long-time and instantaneous trip functions and is designed for use in commercial and industrial power distribution systems.

The Allen-Bradley 800T-XA2 Series D is a 30 mm industrial control contact block featuring two normally open contacts and an A600 NEMA pilot duty rating. Designed for use with Bulletin 800T operators, it provides screw-terminal connections and base-mount installation for industrial control panels.

Leviton 3433-C locking connector delivers 30A, 120/208V 3ØY grounding connectivity in a 4-pole, 4-wire non-NEMA configuration for industrial cord connection.

Hubbell HBL26420 Hubbellock industrial receptacle rated 60A 600V AC, 3-pole 4-wire grounding, screw terminals, cast aluminum long housing.

The Telemotive E7150-1-B is a radio remote control receiver module used in industrial wireless control systems. It functions as the fixed receiving unit that interprets signals from a paired handheld transmitter to control machinery. The module operates as part of a Telemotive radio control system and includes diagnostic indicators for system monitoring and troubleshooting.

The Crouzet PJR 110A P4700 is a plug-in alternator control relay operating on a 110 VAC supply. The module provides SPDT relay output rated at 10 A and is housed in a compact rectangular enclosure with front position indicators. Used in control and protection circuits where monitored voltage conditions determine relay actuation.

The HP A4978-62025 is an LCD and power switch subassembly mounted in a molded plastic bracket. The assembly integrates a monochrome LCD display and a front-panel power switch with a fixed ribbon cable terminating in a D-sub style connector. Identified by assembly label A4978-62025.

SOR 4N3-KK4-N1-C1A-ZZ pressure switch delivers adjustable 2-25 PSI switching for industrial pressure control, with 750 PSI over range and 1000 PSI proof pressure for monitored process applications.

Sprecher + Schuh CS7E-31E control relay with attached CS7-PV auxiliary contact block. Rated for up to 690V AC, this 4-pole industrial control relay is used for switching control circuits in panel and machine control applications.

Steel City RS 2 surface cover provides a durable, galvanized finish for mounting a toggle switch and duplex receptacle on 4" square boxes in exposed installations.