Search results for: 'open'

The HP A4978-62025 is an LCD and power switch subassembly mounted in a molded plastic bracket. The assembly integrates a monochrome LCD display and a front-panel power switch with a fixed ribbon cable terminating in a D-sub style connector. Identified by assembly label A4978-62025.

The Turck B8241-0/PG9 is a field-wireable M12 right-angle, 4-position female connector designed for sensor and actuator wiring in industrial automation. It uses a screw terminal connection, supports 250 V at 4 A, and accepts PG9 cable glands for secure, sealed installations.

The Emerson Ovation WH5D-2FF / 1X00416H03 power supply module provides regulated 24 VDC output for Ovation distributed control system backbones. The enclosed industrial module supports high-current control applications using wide-range AC or DC input power.

Kanson Electronics 1010-1-J-2 off-delay timer relay delivers adjustable 0.5 to 50.0 second timing with 115V 50/60Hz operation and 10 amp output switching for industrial control circuits.

Square D 2510KG1 manual switch delivers reliable 30A control for single-phase systems with a 2-pole toggle design and non-reversing operation in a compact NEMA 1 enclosure.

The Allen-Bradley AK-R2-360P500 Dynamic Brake Resistor is an external medium-duty resistor kit designed for PowerFlex 70 and 700 series drives. It provides 360 ohms of resistance with an 86 watt continuous power rating to dissipate regenerative energy during motor braking.

GE C208LSIR MicroVersaTrip Plus Trip Unit delivers replacement circuit breaker trip control with front-panel setup access, status display, and 800A sensor designation for compatible GE breaker systems.

Tri-Mag Super 6250T2 power supply delivers regulated multi-voltage DC output including +5V, ±12V rails with up to 250 watts capacity for system power distribution and integration applications.

The Siemens 75D73070C AC coil set of 2 offers clearly labeled 50/60 Hz voltage ranges and V/W terminal markings for starter and contactor replacement needs.

The Siemens 3TX4422-0A SIRIUS auxiliary contact block features 2NO + 2NC instantaneous contacts with screw-type terminals. Designed for use with contactor relays and power contactors according to EN 50011, it supports snap-on mounting, IP20 front protection, and positively driven operation per IEC 60947-5-1.

Siemens 771-8STF1 current-to-pneumatic (I/P) transducer converts a DC mA input to a proportional pneumatic output. Configuration: 4–20 mA input, 3–27 psig output, standard output capacity, terminal strip, intrinsically safe approval.

The General Electric CR104PLT43 is a 30.5mm push-to-test indicator light designed for 240V AC industrial automation systems. Part of the GE CR104P series, it utilizes a resistor power supply and supports machine-tool and control panel applications where manual lamp verification is required.

The AEG SH 05.31 is a 4-pole auxiliary contactor from the SH 05 series with a 24V DC coil. It features a 3NO + 1NC contact configuration (31E) and screw terminals. Rated per AC-15 and DC-13 utilization categories as specified in the AEG 2014 extract catalogue.

The Delta AFB1224HE is a 24V DC brushless axial cooling fan designed for reliable airflow in electronic and industrial equipment. It features dual ball bearings, locked rotor protection, and a 120 × 120 × 38 mm frame for consistent thermal management applications.

The Universal 447-LR-TC-P is a 120V magnetic fluorescent ballast designed to operate two lamps in trigger-start configurations. It supports F20T12, F15T8, and F15T12 lamps and features a low power factor, lag-type circuit. UL and CSA certifications support indoor and Type 1 outdoor use.

The Eaton H2006B-3 is a Freedom NEMA heater coil set designed for thermal overload protection in motor control applications. This Class 20 standard trip heater pack supports selectable full load current settings from 1.79A to 2.9A via dial positions A–D and is supplied as a factory-calibrated set of three elements.

The Omron MY4Z DC24(S) is a general-purpose miniature power relay with a 4PDT contact configuration and 24 VDC coil. Rated for 5 A switching in four-pole applications, it is designed for sequence control and power switching in industrial control systems.

The General Electric DS200DDTBG2ABB is an LCI Auxiliary I/O Terminal Board for GE Mark V Speedtronic gas and steam turbine control systems. It provides auxiliary signal termination, conditioning, and isolation for analog and digital I/O in high-voltage industrial control environments.

The Square D 8501NR61 is an 11-pin plug-in relay socket designed for use with compatible Square D relays and timers. It features single-tier screw clamp terminals and supports both panel and DIN rail mounting for industrial control applications.

KATKO KU 380N load break switch delivers 3-pole isolation and switching up to 80A at 690V AC-22, supporting reliable control and disconnection of electrical loads in industrial power systems.

SOR 4N3-KK4-N1-C1A-ZZ pressure switch delivers adjustable 2-25 PSI switching for industrial pressure control, with 750 PSI over range and 1000 PSI proof pressure for monitored process applications.

Wenglor UF88VCF-P24 photoelectric switch sensor supports non-contact object detection for industrial automation with DC operation, fast switching performance, and flexible sensing capability for demanding machine and control tasks.

Minebea NMB-MAT 4715KL-05T-B40 is a 24V DC axial cooling fan with 119 x 119 x 38.4 mm dimensions, 3200 RPM speed, and approximately 118 CFM airflow for industrial equipment cooling.