Search results for: 'panel'

The WAGO 249-117 is a gray, screwless end stop designed to secure DIN-35 rail-mounted terminal blocks. It snaps onto TS 35 x 7.5 mm or 35 x 15 mm rails without tools. Constructed from PA66 polyamide with UL94 V0 flammability rating, it provides stable positioning and electrical insulation.

The ABB DSQC 504 Base Connector Unit is a passive I/O interface module used in ABB robot controller systems. It functions as a centralized backplane for connecting axis control modules, power supplies, safety wiring, and external I/O devices within S4, S4C, and S4C+ controller cabinets.

The Phoenix Contact 560-3889 is a power distribution interface module used within Emerson Ovation distributed control systems. It functions as a marshalling and power distribution interface between controllers and I/O field devices, supporting structured wiring through screw terminal connections in PLC and DCS panels.

The Mitsubishi CP30-BA 1-Pole 5A M-Curve Circuit Protector is a compact DIN-rail-mounted supplementary protector designed for low-capacity control circuits. It features a medium-speed hydraulic-magnetic tripping characteristic, 5 A current rating, and supports AC 250 V or DC 65 V operation in industrial control panels.

Square D 9999 LL0 is a lug-lug kit for Type S contactor and starter configurations, supporting NEMA sizes 00, 0, and 1 in Class 9999 Type LL0 applications.

The TELEMECANIQUE LA4DC1U is a suppressor module designed for use with 3P LP1D09 to LP1D32 contactors. It provides flywheel diode suppression for DC control circuits rated from 24 to 250 V DC and mounts by screws for secure installation.

The Mitsubishi CP30-BA 1-Pole 3A M-Curve Circuit Protector is a compact hydraulic-magnetic supplementary protector designed for low-capacity control circuits. It supports AC 250 V and DC 65 V operation, offers 2.5 kA breaking capacity, and mounts on standard DIN rail using screw terminals.

Kanson Electronics 1010-1-J-2 off-delay timer relay delivers adjustable 0.5 to 50.0 second timing with 115V 50/60Hz operation and 10 amp output switching for industrial control circuits.

Eaton WMZT1C10 offers reliable 10A C-curve protection for 277/480V panels, delivering dependable DIN-rail circuit safety for industrial and commercial systems.

Square D 83713 9070EO2D1 delivers open-type control circuit transformer operation with multi-tap primary input, 110/115/120 V secondary output, and 50/60 Hz ratings for industrial control panels.

Allen-Bradley 1492-UF824 fusible terminal block provides compact DIN-rail circuit protection with LED blown-fuse indication for low-voltage AC/DC control and PLC applications.

Allen-Bradley 100-C12D10 IEC magnetic contactor delivers reliable 12A motor control with 3-pole switching and integrated auxiliary contact, supporting 110V/120V coil operation for industrial control systems.

Phoenix Contact 2832771-HW16 FL Switch SF 8TX delivers reliable 8-port 10/100 Mbps industrial Ethernet expansion with plug-and-play setup and DIN-rail mounting.

Allen-Bradley 193-BSB30 thermal overload relay delivers adjustable 2.0–3.0 A motor protection with Class 10 operation, manual or auto reset selection, and direct-mount Bulletin 193 form factor control.

The Hammond Power CRX06D1BC is a three-phase iron core line reactor rated for 600 VAC and 6.1 A. Part of the HPS Centurion® R Series, it provides controlled impedance to mitigate harmonics and electrical transients in AC drive systems operating at 50/60 Hz.

The Edwards Signaling 48XBRMG120A is a green LED visual signal light designed for indoor and outdoor industrial applications. Operating on 120 VAC, this dual-mode beacon supports steady-on or flashing operation and is housed in a corrosion-resistant NEMA 4X enclosure.

KATKO KU 380N load break switch delivers 3-pole isolation and switching up to 80A at 690V AC-22, supporting reliable control and disconnection of electrical loads in industrial power systems.

The Mitsubishi SR-T5 AC100V 3A2B contactor relay is designed for control circuits requiring reliable auxiliary switching. It operates on a 100–127 VAC coil and provides 3 normally open and 2 normally closed contacts. The compact design supports DIN rail or screw mounting.

The Weidmüller 1122-8800-00 TRZ 24VDC 1CO is a slim DIN rail relay interface module with a 24 V DC control voltage and one changeover (SPDT) contact. It supports up to 6 A switching current and uses tension-clamp connections for secure, screwless wiring in control cabinets.

Allen-Bradley 1492-FB3J60-L fuse holder provides secure Class J fuse mounting for control applications, supporting reliable protection in industrial systems.

Allen-Bradley 193-T1AB48 bimetallic overload relay delivers adjustable 3.5-4.8 A motor overload protection with Class 10 tripping, phase-loss sensitivity, and manual or automatic reset for motor starter assemblies.

Allen-Bradley 100-C16D*10 motor contactor built for switching motor loads in industrial control systems, featuring a 110-120V AC coil, 3-pole power contacts, and 1 NO auxiliary contact for control circuit integration.

The Ferraz Shawmut UltraSafe USCC2 P216489 is a 2-pole modular fuse holder rated for 30A and 600 VAC/VDC for Class CC fuses. Designed for DIN rail mounting, it features IP20 finger-safe protection, pressure plate terminals, and a 200 kA SCCR for industrial control panel applications.

Mitsubishi TH-T25KP thermal overload relay provides 3-element overload protection with a 1.7 A heater designation, 1.4–2 A setting range, and auxiliary NO/NC contacts for industrial motor control circuits.

Square D FAL34050 delivers 50A, 3-pole thermal-magnetic circuit protection for 480V electrical systems with unit-mount installation and line/load lug connections.