Search results for: 'Chimpancé'

The Siemens 3TX4422-0A SIRIUS auxiliary contact block features 2NO + 2NC instantaneous contacts with screw-type terminals. Designed for use with contactor relays and power contactors according to EN 50011, it supports snap-on mounting, IP20 front protection, and positively driven operation per IEC 60947-5-1.

Siemens 771-8STF1 current-to-pneumatic (I/P) transducer converts a DC mA input to a proportional pneumatic output. Configuration: 4–20 mA input, 3–27 psig output, standard output capacity, terminal strip, intrinsically safe approval.

The Struthers-Dunn W88AHPX-36 is a hermetically sealed 3PDT plug-in relay from the 88HP Series, rated 10A and configured for 120VAC operation. It features an 11-pin octal base and a sealed gray metal enclosure designed to prevent contamination and corrosion.

The Universal 447-LR-TC-P is a 120V magnetic fluorescent ballast designed to operate two lamps in trigger-start configurations. It supports F20T12, F15T8, and F15T12 lamps and features a low power factor, lag-type circuit. UL and CSA certifications support indoor and Type 1 outdoor use.

The Allen-Bradley AK-R2-360P500 Dynamic Brake Resistor is an external medium-duty resistor kit designed for PowerFlex 70 and 700 series drives. It provides 360 ohms of resistance with an 86 watt continuous power rating to dissipate regenerative energy during motor braking.

The Allen-Bradley 800B-PS11 is a 16 mm snap-action contact block with one normally open and one normally closed contact. Designed for Bulletin 800B push button and selector switch operators, it supports reliable low-voltage switching and compact panel installations in light industrial and instrumentation applications.

The Edwards Signaling 48XBRMG120A is a green LED visual signal light designed for indoor and outdoor industrial applications. Operating on 120 VAC, this dual-mode beacon supports steady-on or flashing operation and is housed in a corrosion-resistant NEMA 4X enclosure.

The General Electric DS200DDTBG2ABB is an LCI Auxiliary I/O Terminal Board for GE Mark V Speedtronic gas and steam turbine control systems. It provides auxiliary signal termination, conditioning, and isolation for analog and digital I/O in high-voltage industrial control environments.

The GE DS200VPBLG1AFF is a VME P2 backplane board used in GE LS2100 and Load Commutated Inverter control systems. It provides centralized power and signal distribution across a 13-slot chassis, supporting DSPC, gate distribution, exciter, and I/O extender boards.

The ABB 1SVR427014R0000 CP-S 24/5.0 is a 120 W DIN rail switch mode power supply delivering 24 V DC at 5 A. Designed for industrial environments, it supports wide AC and DC input ranges, adjustable output voltage, high efficiency, and integrated protection features for reliable system power.

The Phoenix Contact RAD-OUT-8D-REL is an 8-channel digital relay output extension module for Radioline wireless systems. It provides floating relay contacts for reliable signal switching and supports DIN rail mounting in industrial automation environments.

The C3 Controls DDS2-340-DHGRY is a non-fused, 40 amp, 3-pole disconnect switch designed for door-mount applications. It features a red/yellow rotary operating handle and an IP65 ingress protection rating for use in industrial control environments requiring reliable circuit isolation.

The General Electric CR305X100E is a side-mounted auxiliary contact adder block providing one normally closed (1 NC) contact for GE 200- and 300-Line starters and contactors. It is designed for field installation onto a basic auxiliary contact block and is rated up to 600 VAC and 250 VDC.

The Square D 8501NR61 is an 11-pin plug-in relay socket designed for use with compatible Square D relays and timers. It features single-tier screw clamp terminals and supports both panel and DIN rail mounting for industrial control applications.

Phoenix Contact 2832771-HW16 FL Switch SF 8TX delivers reliable 8-port 10/100 Mbps industrial Ethernet expansion with plug-and-play setup and DIN-rail mounting.

SCHMERSAL SRB301LCI-24V: Reliable 24V safety controller relay with 3 safety contacts, signaling output, and advanced diagnostics for industrial protection.

Eaton DILM12-10 XTCE012B10A XT IEC contactor provides 12A three-pole full-voltage non-reversing control with 110–120 Vac coil, 1 NO contact configuration, and screw terminals.

Amperite 115C60 thermal time delay relay delivers fixed 60-second Delay on Break control with 115V AC/DC input, SPST-NC contacts, and a 3A resistive rating.

KATKO KU 380N load break switch delivers 3-pole isolation and switching up to 80A at 690V AC-22, supporting reliable control and disconnection of electrical loads in industrial power systems.

Mitsubishi TH-T25KP thermal overload relay provides 3-element overload protection with a 1.7 A heater designation, 1.4–2 A setting range, and auxiliary NO/NC contacts for industrial motor control circuits.

Eaton C0200E2AFB delivers 200 VA industrial control transformer performance with multi-voltage primary input and 120/115/110 V secondary output for control circuit power.

Schneider Electric Telemecanique LC1 D09 10 is a 3-pole magnetic contactor for AC motor control and circuit switching, with an integrated 1 NO auxiliary contact and motor-starting capability up to 4 kW at 400V.

Allen-Bradley 100-C16D*10 motor contactor built for switching motor loads in industrial control systems, featuring a 110-120V AC coil, 3-pole power contacts, and 1 NO auxiliary contact for control circuit integration.