Search results for: 'designated、'

The General Electric 8G163WF is a fluorescent lamp ballast labeled for 277-volt operation and F48CW lamp applications. This unit is identified directly from manufacturer carton labeling and is supplied as a single ballast. No additional accessories or documentation are included.

The Fisher R3570CX0022 is a pneumatic valve positioner repair kit intended for maintenance of Fisher 3570 Series pneumatic valve positioners. This kit supports servicing of positioners used in industrial control valve assemblies and is not a complete valve or positioner.

Schneider Electric 9001KU7 is a clear silicone rubber push button boot for Harmony 9001K and 9001SK non-illuminated 30 mm push buttons.

The General Electric CR305X100E is a side-mounted auxiliary contact adder block providing one normally closed (1 NC) contact for GE 200- and 300-Line starters and contactors. It is designed for field installation onto a basic auxiliary contact block and is rated up to 600 VAC and 250 VDC.

Allen Bradley 700S-CFB440KDC Safety Relay: Reliable 110V industrial control relay. Built for precision, durability, and seamless performance in demanding environments.

The Allen-Bradley 800FM-MT44 is a metal emergency stop push button operator with a 40 mm red mushroom actuator and twist-to-release operation. Designed for 22.5 mm panel mounting, this non-illuminated operator is part of the Bulletin 800FM metal series for industrial control applications.

The Omron PTF08A-E is an 8-pin relay socket designed for use with Omron LY series SPDT and DPDT general-purpose relays. It supports DIN rail mounting and can also be screw-mounted. The socket features touch-safe screw terminals and is constructed for secure relay retention and field wiring integration in industrial control panels.

The Allen-Bradley 800B-EAB is a 16 mm maintained square push button operator designed for light industrial and instrumentation applications. It features corrosion-proof plastic construction and gold-plated snap-action contact compatibility for reliable low-voltage switching when paired with Bulletin 800B contact blocks.

The Siemens 3SU1400-1AA10-1BA0 is a SIRIUS ACT contact module with one normally open contact. It features screw terminals and a snap-on design for front plate mounting behind compatible actuators. Designed for industrial control and signaling applications requiring reliable signal switching.

OmniOn Power 2007001F is a control and monitoring circuit board for Infinity D DC power systems, supporting reliable telecom and data-center power management.

The C3 Controls DDS2-340-DHGRY is a non-fused, 40 amp, 3-pole disconnect switch designed for door-mount applications. It features a red/yellow rotary operating handle and an IP65 ingress protection rating for use in industrial control environments requiring reliable circuit isolation.

The Schrack ZG400615 is a used ice cube relay rated for 5 Amps and up to 600 Volts. It features a 14-pin plug-in design and a 115 VAC coil voltage, making it suitable for general industrial control and electrical switching applications where reliable electromechanical control is required.

The Tristar S0803-0000 is a compact 12V DC white LED indicator designed for 1/2" hole mounting. This polarity-sensitive LED draws approximately 0.02–0.03 amps and consumes about 0.25 watts. The unit features a 1/2" diameter body with a 1.75" housing length and is suitable for low-draw DC indicator applications.

The Murr Elektronik 23050 is a three-phase RC motor suppressor designed to reduce induced voltage peaks in AC motor applications. Rated for up to 575 VAC at 50/60 Hz and 4 kW engine power, it supports star-connected RC suppression and installation close to the interference source.

The Universal 827-SLH-TC-P is a magnetic instant-start fluorescent ballast designed to operate two slimline lamps on a 277V, 60 Hz power supply. It supports series lamp operation and is intended for replacement use in compatible commercial and industrial lighting fixtures.

The Allen-Bradley 800B-N5W is a white LED lamp designed for use with Bulletin 800B 16 mm illuminated push-button and pilot light operators. Rated for 120V AC operation, this LED bulb provides consistent white illumination with low power consumption and extended service life in industrial control panel applications.

The General Electric CR104PLT43 is a 30.5mm push-to-test indicator light designed for 240V AC industrial automation systems. Part of the GE CR104P series, it utilizes a resistor power supply and supports machine-tool and control panel applications where manual lamp verification is required.

Schneider Electric CAD50G7 is a TeSys Deca control relay with five normally open contacts and a 120 VAC 50/60 Hz control coil. Rated up to 690 VAC and 10 A, it supports DIN rail or panel mounting and is designed for industrial control circuit applications.

The Universal 447-LR-TC-P is a 120V magnetic fluorescent ballast designed to operate two lamps in trigger-start configurations. It supports F20T12, F15T8, and F15T12 lamps and features a low power factor, lag-type circuit. UL and CSA certifications support indoor and Type 1 outdoor use.

The Hammond Power CRX06D1BC is a three-phase iron core line reactor rated for 600 VAC and 6.1 A. Part of the HPS Centurion® R Series, it provides controlled impedance to mitigate harmonics and electrical transients in AC drive systems operating at 50/60 Hz.

The Allen-Bradley 800T-XA2 Series D is a 30 mm industrial control contact block featuring two normally open contacts and an A600 NEMA pilot duty rating. Designed for use with Bulletin 800T operators, it provides screw-terminal connections and base-mount installation for industrial control panels.

Allen-Bradley 100-D-S1-11 auxiliary contact block adds 1NO/1NC control contacts to 100-D series contactors, offering reliable screw-terminal expansion for industrial panels.

Square D 9001 TS-1 selector switch operator delivers 2-position manual control for industrial panel systems requiring reliable mechanical switching input.

Mitsubishi TH-T25KP thermal overload relay provides 3-element overload protection with a 1.7 A heater designation, 1.4–2 A setting range, and auxiliary NO/NC contacts for industrial motor control circuits.