Search results for: 'base out'

Moore Industries RBX/3W80-160/4-20MA/12-42DC-EZ100[HP] resistance bulb transmitter with 3-wire RTD input, 4-20mA output, 12-42VDC loop power, and front Zero/Span adjustment.

SKF CMSS65-010-00-12-10 is a CMSS 65 series 5 mm eddy current probe with armored cable, 1/4-28 threaded fully threaded case, 3.0 cm case length, and 1.0 m overall length.

RaySafe Xi light meter with B Light Probe for luminance and illuminance measurement in medical diagnostic X-ray imaging environments, including display and ambient light assessment.

INNO Instrument PAC-1006 large alligator clip adapter set with red and black insulated clips, safety connector interface, and 600V CAT IV 19A rating.

Eagle Eye HGD-4000 hydrogen gas detector with intrinsically safe design, AC power input (85–265 VAC), dual internal alarm relays, and LED status indication.

Eagle Eye HGD-2000-C3 Control Box with 3 Sensors Compatible with HGD-2000 for monitoring hydrogen gas buildup in battery rooms and similar facilities. Features dual relays, audible alarm, and AC power input.

The ABB OHDI-01 is a 115/230 VAC digital input module designed for use with ABB ACS550, ACH550, and ACS800 drives. It converts high-voltage digital input signals to 24 VDC drive inputs and supports up to six 115 VAC inputs or three 230 VAC inputs.

The INNO Instrument DIN-18 is a DC power cable designed to connect compatible INNO TS-Pro or TS-Plus thermal strippers to the power output port of supported INNO View series fusion splicers. It enables field operation by allowing the thermal stripper to draw power directly from the splicer’s internal battery.

The Opto 22 AD6T is a single-channel, optically isolated analog input module designed for 0–5 VDC signals. Built in Opto 22 G1 (Standard) form factor, it provides 12-bit resolution, 4,000 VRMS isolation, and compatibility with Standard analog I/O racks for industrial control systems.

Fluke I410 AC/DC current clamp adapter expands digital multimeters to measure 1A–400A AC/DC using Hall-effect sensing with 1mV/A output, enabling safe, non-intrusive current measurements.

Fluke i200 AC current clamp enables accurate 0.5–200A AC measurements using a multimeter. Features 1 mA/A output, banana plug interface, and CAT III 600V safety for electrical testing.

Omega CN78030 delivers precise PID temperature and process control in a compact 1/16 DIN format, featuring relay output, universal sensor input, RS485 communication, and advanced autotune and fuzzy logic control.

The GE ConnectPort X4-H ZB HSPA+ is an industrial cellular and ZigBee routing gateway designed for remote asset monitoring in water treatment and power applications. It combines HSPA+ cellular connectivity with ZigBee mesh networking in a rugged NEMA 4X enclosure.

The General Electric DS200DDTBG2ABB is an LCI Auxiliary I/O Terminal Board for GE Mark V Speedtronic gas and steam turbine control systems. It provides auxiliary signal termination, conditioning, and isolation for analog and digital I/O in high-voltage industrial control environments.

Yamatake Honeywell 8240-7444-001 ENH Relay Terminal Panel. This panel provides relay termination using multiple installed plug-in relays and numbered screw terminals on a single PCB assembly. Identified by manufacturer silkscreen and assembly number only.

The Yamatake Honeywell J-HMM00 is a high-level analog input module designed for Distributed Control System (DCS) architectures. Operating on 24 VDC with 60 mA current consumption, it supports multi-point analog signal acquisition for integration within compatible control systems such as MSC10.

The Phoenix Contact 560-3889 is a power distribution interface module used within Emerson Ovation distributed control systems. It functions as a marshalling and power distribution interface between controllers and I/O field devices, supporting structured wiring through screw terminal connections in PLC and DCS panels.

Pomona 1296 BNC male to dual stacking binding post adapter converts BNC test instruments to banana jack connections, supporting stacked binding posts for flexible laboratory and bench testing setups.

The Emerson Fisher-Rosemount KJ4001X1-CA1 is an I/O terminal block used as an interface between field wiring and control system I/O modules. The unit provides 16 numbered terminal positions and is designed for industrial automation installations, including hazardous location environments as indicated on the device label.

The Square D 8501NR61 is an 11-pin plug-in relay socket designed for use with compatible Square D relays and timers. It features single-tier screw clamp terminals and supports both panel and DIN rail mounting for industrial control applications.

Fluke 787B ProcessMeter combines a safety-rated digital multimeter with mA loop calibrator functions, enabling accurate measurement, sourcing, and simulation for industrial current loop troubleshooting.

Fluke Networks GLD-DSX-5000MI Gold Support delivers 1-year maintenance for DSX-5000 systems, including 24/7 technical support, software and firmware updates, calibration, repairs, and parts replacement.

Fluke Networks GLD3-DSX-5000QI Gold Support provides 3 years of calibration, repairs, loaner service, and 24/7 technical support for DSX-5000Qi.

Fluke Networks GLD3-CFP-100-M Gold Support delivers 3-year maintenance coverage for the CFP-100-M, including calibration, repair, parts replacement, and priority technical support.

Allen-Bradley 1336-RLOAD-SP2A load resistor module engineered for 1336 PLUS, PLUS II, FORCE, and IMPACT drives, providing controlled regenerative and braking energy dissipation in supported voltage ranges.