Search results for: 'opens'

Eaton Bussmann 2432B59 semiconductor fuse delivers 10A, 250V high-speed protection for sensitive power electronics with a ceramic body and 200,000A interrupting rating in a pack of 10.

GE C208LSIR MicroVersaTrip Plus Trip Unit delivers replacement circuit breaker trip control with front-panel setup access, status display, and 800A sensor designation for compatible GE breaker systems.

Tri-Mag Super 6250T2 power supply delivers regulated multi-voltage DC output including +5V, ±12V rails with up to 250 watts capacity for system power distribution and integration applications.

The Siemens 75D73070C AC coil set of 2 offers clearly labeled 50/60 Hz voltage ranges and V/W terminal markings for starter and contactor replacement needs.

SKF CMSS65-010-00-12-10 is a CMSS 65 series 5 mm eddy current probe with armored cable, 1/4-28 threaded fully threaded case, 3.0 cm case length, and 1.0 m overall length.

Fisher CCLAMP-5-MF inductive clamp for TW9000 enables non-contact signal transfer. Designed for multi-frequency utility locators, it induces tracing signals onto exposed conductors up to 5 inches.

The ABB OHDI-01 is a 115/230 VAC digital input module designed for use with ABB ACS550, ACH550, and ACS800 drives. It converts high-voltage digital input signals to 24 VDC drive inputs and supports up to six 115 VAC inputs or three 230 VAC inputs.

The Siemens 3TX4422-0A SIRIUS auxiliary contact block features 2NO + 2NC instantaneous contacts with screw-type terminals. Designed for use with contactor relays and power contactors according to EN 50011, it supports snap-on mounting, IP20 front protection, and positively driven operation per IEC 60947-5-1.

Siemens 771-8STF1 current-to-pneumatic (I/P) transducer converts a DC mA input to a proportional pneumatic output. Configuration: 4–20 mA input, 3–27 psig output, standard output capacity, terminal strip, intrinsically safe approval.

The General Electric CR104PLT43 is a 30.5mm push-to-test indicator light designed for 240V AC industrial automation systems. Part of the GE CR104P series, it utilizes a resistor power supply and supports machine-tool and control panel applications where manual lamp verification is required.

The GE Fanuc IC693CHS392G is a 10-slot expansion I/O baseplate for the Series 90-30 PLC platform. It features a 25-pin D-type expansion connector, rack address DIP switch, and supports local I/O expansion up to 50 feet. Designed for use with compatible CPU baseplates.

The AEG SH 05.31 is a 4-pole auxiliary contactor from the SH 05 series with a 24V DC coil. It features a 3NO + 1NC contact configuration (31E) and screw terminals. Rated per AC-15 and DC-13 utilization categories as specified in the AEG 2014 extract catalogue.

The Delta AFB1224HE is a 24V DC brushless axial cooling fan designed for reliable airflow in electronic and industrial equipment. It features dual ball bearings, locked rotor protection, and a 120 × 120 × 38 mm frame for consistent thermal management applications.

The Universal 447-LR-TC-P is a 120V magnetic fluorescent ballast designed to operate two lamps in trigger-start configurations. It supports F20T12, F15T8, and F15T12 lamps and features a low power factor, lag-type circuit. UL and CSA certifications support indoor and Type 1 outdoor use.

Fluke i200S AC Current Clamp delivers accurate non-intrusive AC current measurement from 0.5A to 240A using a BNC voltage output, ideal for multimeters, oscilloscopes, and power quality tools.

Fluke FTP17XXPQ fused test probe set delivers secure voltage indication for three-phase power quality testing, using 11A fused probes and AC285 alligator clips designed for Fluke analyzers and loggers.

The Eaton H2006B-3 is a Freedom NEMA heater coil set designed for thermal overload protection in motor control applications. This Class 20 standard trip heater pack supports selectable full load current settings from 1.79A to 2.9A via dial positions A–D and is supplied as a factory-calibrated set of three elements.

The Omron MY4Z DC24(S) is a general-purpose miniature power relay with a 4PDT contact configuration and 24 VDC coil. Rated for 5 A switching in four-pole applications, it is designed for sequence control and power switching in industrial control systems.

The KAMAN Sensors digiVIT 855949-000 is a self-tuning digital driver for non-contact inductive and eddy current position and displacement sensors. It features pushbutton calibration, embedded intelligence, selectable analog outputs, and Ethernet connectivity for monitoring and parameter switching.

Fluke 302+ digital clamp meter delivers reliable 400A AC current and 600V AC/DC measurements in a compact handheld design with backlit display, built for everyday electrical troubleshooting and maintenance tasks.

The MIP LM 3086 EPA3 is a laser-based opacity and dust monitor designed for continuous emissions monitoring in industrial stacks. It uses a single-pass, dual-path laser architecture with an optical reference path to measure opacity, optical density, and calibrated dust concentration values.

Honeywell 380-01873-100 I/O Interface Module enables remote monitoring and control of field devices using RS485 Panel Bus™ communication with 34 configurable I/O points for scalable building automation systems.

The General Electric DS200DDTBG2ABB is an LCI Auxiliary I/O Terminal Board for GE Mark V Speedtronic gas and steam turbine control systems. It provides auxiliary signal termination, conditioning, and isolation for analog and digital I/O in high-voltage industrial control environments.

This CCC Series 4 temperature input module set includes one IOM TCW (I-1/201-2/200) and one EIOM TCW (E-1/202-3/200). Both modules are designed for 3-wire GDC RTD temperature inputs and chassis mounting within CCC Series 4 control systems.

The Square D 8501NR61 is an 11-pin plug-in relay socket designed for use with compatible Square D relays and timers. It features single-tier screw clamp terminals and supports both panel and DIN rail mounting for industrial control applications.