Search results for: 'after with'

The new digiPHONE+2. A combination of different methods for efficient noise damping enables perfect acoustics that lets you hear only the fault noise.

The V-2410 Three-Way Multipurpose Solenoid Air Valve is used in applications where an electrical circuit operates a pneumatic control device. This valve diverts the air signal to the pneumatic device when the coil is energized or de-energized, depending on the choice of air connection.

Greystone - Sensor Type 12 - Pt1000-1000 ohm Platinum RTD. Immersion 100mm (4") c/w ABS utility box -requires thermowell Probe Sensors. The TE200 Series temperature sensors offer a choice of precision platinum RTD's, IC's, or NTC thermistor sensors which can be interfaced with a computerized monitoring or control system.

Fluke Networks MMC-62-SCSC Launch Cable is a multimode SC/SC fiber optic cable, is used for high-speed networks installation, inspection and troubleshooting. An OTDR requires launch cables or fiber rings to measure the end-to-end loss of fiber optic links. The multimode fiber has a 62.5/125µm core/cladding diameter.Length is 105 meters.

Fluke Networks MMC-62-SCSC Launch Cable is a multimode SC/SC fiber optic cable, is used for high-speed networks installation, inspection and troubleshooting. An OTDR requires launch cables or fiber rings to measure the end-to-end loss of fiber optic links. The multimode fiber has a 62.5/125µm core/cladding diameter.Length is 105 meters.

Multimode launch cable 50μm SC/SC. Fluke Networks MMC-50-SCSC Launch Cable is a multimode SC/SC fiber optic cable which is used for high-speed networks installation, inspection and troubleshooting. The multimode fiber has a 50/125µm core/cladding diameter. Length is 105 meters.

The 42N50A-30 coaxial fixed attenuator provides 30 dB attenuation and a 50 watt power rating for high power measurements.Fixed attenuator30 dB attenuation50 watt power rating

Schneider Electric’s remote racking Masterpact NW circuit breakers is designed is reduce the arc flash safety hazard for personnel during installation, startup and maintenance procedures. The Masterpact NW remote racking device provides maintenance personnel the ability to rack a low-voltage draw-out breaker from a remote location. This allows the personnel to be clear of the arc flash boundary area.

Inline Ratcheting Head for Low Profile Hydraulic Ratcheting Wrenches Inline IU-XL.

Inline Ratcheting Head for Low Profile Hydraulic Ratcheting Wrenches Inline IU-XL.

Inline Ratcheting Head for Low Profile Hydraulic Ratcheting Wrenches Inline IU-XL.

Fujikura FSM-50S SM MM Fiber Core Alignment Fusion Splicer w/ Cleaver CT-30 50 S

The Ti200 infrared camera delivers the flexibility and performance to allow you to stay on top of innovation, whether it's through industrial or commercial applications. You'll be able to spectrum analyze, detect heat and radiation level variations, or use it for industrial process control — all with wireless speed and ease. And, since it's future-ready, no matter what comes next for your business, so long as you have an infrared camera on hand, you'll be ready.

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

This set of Permanent Link Adapters from Fluke Networks comes with two tips, two latches, two screws, two top and bottom cases, and two conductive washers. The adapters meet all measurement accuracy specifications for Level IV test equipment, with a typical contact life of over 5,000 cycles. Each adapter measures 3.0 inches by 2.1 inches by 1.2 inches, has a 4.85-foot cable, and weighs approximately 2.4 ounces (channel adapter) or 11.7 ounces (permanent link adapter).

The DTX-MFM2 fiber module are used with a DTX Series Cable Analyzer to test and certify fiber optic cabling installations. 

The DSX-PLA004/CHA004 permanent link and channel adapters meet all measurement accuracy specifications for Level IV test equipment. The life of module contacts is >5,000 cycles. Dimensions are 3.0 in x 2.1 in x 1.2 in (75 mm x 54 mm x 30 mm). The permanent link adapter has a 4.85 ft (1.48 m) ±0.25 ft (0.1 m) cable. Weight is ~2.4 oz (68 g) for the channel adapter and ~11.7 oz (332 g) for the permanent link adapter.

VIEW5 PRO’s 5-inch high-resolution color LCD touch screen with user-friendly intuitive GUI (Graphic User Interface) offers large and clear fiber images to users. By double-tapping the screen, users can Zoom In & Out the image to the world’s highest magnification of 520x. The fusion splicer is equipped with bua ilt-in IoT module that connects to the INNO’s View Pro Cloud Management System for real-time operation and management online. This innovative cloud-based solution is designed to create the most advanced and yet most uncomplicated splicing and work experiences ever.

The TE-6700 Seriesis attractively styled, feature-packed temperature sensing products offer ease of installation, user friendliness, and application flexibility in one package.

Product Overview

The CFP2-100-Q CertiFiber Pro Quad Optical Loss Test Set (OLTS) helps cabling professionals accomplish more than ever and comes with a Wi-Fi adapter for wireless connectivity to Fluke Networks LinkWare Live software. It's all about accurate, error-free certification, making jobs easier to manage and certifying fiber optic cabling to industry standards, faster.