Search results for: 'control for'

Emerson KJ3222X1-BK1 is a DeltaV S-Series analog input module with 8 channels for 4-20 mA HART signals. The module is identified on manufacturer documentation as AI 8 CH 4-20mA HART CARD.

Hubbell CS320I is a commercial-specification 3-way toggle switch rated 20A at 120/277V AC. It is side wired only, supports #14 to #10 AWG copper wire, and features an ivory nylon toggle with thermoplastic construction.

WAGO 750-452 Analog Input Module delivers reliable PLC current signal acquisition for WAGO 750 I/O nodes, enabling precise control in industrial automation.

Moeller PKZM0-2.5 motor protection circuit breaker with attached NHI11-PKZ0 side module. Front rotary handle, 1.6-2.5 A adjustment dial, and three-pole terminal layout as shown.

Square D 9001SKP1C9 delivers 30 mm pilot light signaling with a red domed plastic lens, incandescent BA 9s lamp, 110–120 V AC supply, and screw clamp terminals.

The NOARK Ex9S32A32A is a 3-pole thermal-magnetic manual motor starter with an adjustable 24–32A current setting range and Class 10 overload protection. Designed for motor branch circuit protection, it provides manual isolation, manual motor control, and short-circuit protection with rotary handle operation.

WOHLER Locking Lever for Large Viper – Elevate Your Efficiency and Precision!

Schneider Electric 9001KU7 is a clear silicone rubber push button boot for Harmony 9001K and 9001SK non-illuminated 30 mm push buttons.

The ABB Bailey IMASI02 is an Analog Slave Input module for the Infi 90 Process Management System. It converts analog field signals into digital data for processing by a Multi-Function Processor and interfaces up to fifteen process signals through a single MMU slot.

The Emerson Fisher-Rosemount KJ4001X1-CA1 is an I/O terminal block used as an interface between field wiring and control system I/O modules. The unit provides 16 numbered terminal positions and is designed for industrial automation installations, including hazardous location environments as indicated on the device label.

Allen-Bradley 1336-RLOAD-SP2A load resistor module engineered for 1336 PLUS, PLUS II, FORCE, and IMPACT drives, providing controlled regenerative and braking energy dissipation in supported voltage ranges.

Automation Direct D4-08B-1 DL405 8-slot I/O base delivers reliable panel-mounted rack support for DirectLOGIC 405 PLC systems needing flexible modular expansion.

The Opto 22 AD6T is a single-channel, optically isolated analog input module designed for 0–5 VDC signals. Built in Opto 22 G1 (Standard) form factor, it provides 12-bit resolution, 4,000 VRMS isolation, and compatibility with Standard analog I/O racks for industrial control systems.

The Hammond Power CRX06D1BC is a three-phase iron core line reactor rated for 600 VAC and 6.1 A. Part of the HPS Centurion® R Series, it provides controlled impedance to mitigate harmonics and electrical transients in AC drive systems operating at 50/60 Hz.

The Allen-Bradley 1492-SP1C250 is a single-pole, 25 A supplementary circuit breaker with a Type C tripping characteristic. Designed for DIN rail mounting, it provides thermal-magnetic overcurrent protection for commercial and light industrial control circuits operating with inductive loads.

The MIP LM 3086 EPA3 is a laser-based opacity and dust monitor designed for continuous emissions monitoring in industrial stacks. It uses a single-pass, dual-path laser architecture with an optical reference path to measure opacity, optical density, and calibrated dust concentration values.

The ABB Bailey IMFCS01 is an intelligent Frequency Counter Slave Module for INFI 90 and Net 90 DCS platforms. It processes high-speed pulse inputs from field sensors and communicates frequency and period data to a Multi-Function Processor via the slave expander bus for speed monitoring and control.

Fluke TP175 TwistGuard test probes deliver adjustable 2mm probe tips with CAT IV 600V safety ratings, providing controlled tip exposure for secure electrical measurements across compatible Fluke test leads.