Search results for: 'for'

The Fluke CO-220 is a handheld carbon monoxide meter designed to detect and measure CO concentrations from 0 to 1000 ppm. It uses a stabilized electrochemical, gas-specific sensor and provides both numeric LCD readings and an audible beeper response. Features include MAX Hold, automatic backlight, sensor self-test, and automatic power-off.

Yamatake Honeywell 8240-7444-001 ENH Relay Terminal Panel. This panel provides relay termination using multiple installed plug-in relays and numbered screw terminals on a single PCB assembly. Identified by manufacturer silkscreen and assembly number only.

Fluke FEV150 BASIC EV charging station analyzer tests safety and performance of AC chargers with guided workflows and control pilot simulation.

Elcometer 331 TH Deep Cover Concrete Covermeter & Half Cell Gauge for reinforced concrete surveys requiring rebar location, cover depth measurement, bar sizing, and TH linear/grid data logging.

The Fluke Networks LinkIQ LIQ-KIT-FMC Cable & Network Tester Kit verifies twisted pair and fiber performance up to 10GBASE-T and supports network troubleshooting. It provides frequency-based bandwidth validation, wiremap, distance to fault, IPv4/IPv6 ping, nearest switch diagnostics, and PoE testing, with RJ-45, USB, and SFP connectivity.

The Honeywell 621-9939 Serial Link Module is a communication interface for Honeywell Series 9000 and IPC 620 control systems. It manages serial I/O data exchange between the main processor and distributed serial devices using dual asynchronous channels and RS485 connectivity.

Phoenix Contact QUINT-DIODE/12-24DC/2X20/1X40 is a DIN-rail mounted redundancy diode module for 12–24 V DC systems. It decouples parallel power supplies to increase system availability, supporting 2×20 A redundancy or 1×40 A increasing power operation.

The Fluke LIQ-DUO-KIT-6PK contains six LinkIQ Duo tester kits, each capable of 10 Gb/s cable testing, network switch diagnostics, PoE verification, and Wi-Fi analysis. This bundle is suited for larger technician teams and multi-site deployments.

FTTH Innovations FIG air blown microfibre installation tool with electronic push force control and cruise control mode for controlled fibre installation in microduct at speeds up to 100 m/min.

Eaton DILM12-10 XTCE012B10A XT IEC contactor provides 12A three-pole full-voltage non-reversing control with 110–120 Vac coil, 1 NO contact configuration, and screw terminals.

The PLS 6R RBP KIT is a self-leveling cross line and point red laser level designed for plumb, level, and square layout applications. It provides 180° horizontal and 130° vertical fan angles with ≤1/8 in accuracy at 30 ft. This kit includes the RBP5 rechargeable Li-ion battery pack, alkaline battery pack, floor stand, magnetic L-bracket, UB9 wall/ceiling bracket, and reflective target.

Allen-Bradley PHOTOSWITCH Series 9000 transmitted beam receiver sensor (42GRR-9003-QD, Series A) with 70–264V AC/DC operation, isolated N.O. solid-state (MOSFET) output, 4-pin AC Micro quick-disconnect, and IR 880 nm optics.

The Saft LS33600 is a 3.6 V primary lithium-thionyl chloride (Li-SOCl₂) D-size battery designed for long-term, low-to-moderate current applications. It provides a nominal capacity of 17.0 Ah, stable voltage output, and a wide operating temperature range from −60°C to +85°C. This non-rechargeable cell is commonly used in utility metering, industrial electronics, and professional equipment.

Allen-Bradley 193-EEDB E1 Plus electronic overload relay provides precise three-phase motor protection with adjustable 3.2–16A current range, selectable trip classes, and direct mounting to 100-C IEC contactors.

Moeller PKZM0-2.5 motor protection circuit breaker with attached NHI11-PKZ0 side module. Front rotary handle, 1.6-2.5 A adjustment dial, and three-pole terminal layout as shown.

INNO Instrument SPA1000 digital power meter with 1 power channel, AC/DC measurement, 100 kHz bandwidth, up to 1000 V and 20 A input, 4-item LED display, and harmonic measurement to the 100th order.

The Fluke 87V/PRV240 Digital Multimeter Kit combines the Fluke 87V Industrial Digital Multimeter with the PRV240 Proving Unit. The 87V supports AC/DC voltage and current measurement up to 1000 V and 10 A, resistance to 50 MΩ, capacitance, frequency to 200 kHz, and temperature from -200°C to 1090°C. The PRV240 provides a portable 240 V AC/DC source for verifying proper meter operation before testing.

Fisher TW9000-HC is a multi-frequency digital line tracer for locating buried pipes and cables. It supports direct connection, inductive, passive power, sonde, and coupling clamp locating methods.

Certified pre-owned VIAVI SmartClass Fiber OLP-82P—handheld optical power meter with integrated patch-cord microscope (PCM), 780–1650 nm coverage, storage for up to 10,000 results, and USB/FiberChekPRO reporting.