Search results for: 'safety in'

The Universal 447-LR-TC-P is a 120V magnetic fluorescent ballast designed to operate two lamps in trigger-start configurations. It supports F20T12, F15T8, and F15T12 lamps and features a low power factor, lag-type circuit. UL and CSA certifications support indoor and Type 1 outdoor use.

Fluke 190-104-III-S portable ScopeMeter oscilloscope delivers 100 MHz bandwidth, four isolated channels, and rugged field performance for industrial waveform analysis and troubleshooting.

Fluke 87-5 CAL Industrial Multimeter: True RMS digital readings, fast peak capture, low-pass filter support, and backlit display for efficient troubleshooting.

AEMC 6422 Digital Ground Resistance Tester Kit 150ft: Fast 3-point testing with auto-ranging, large LCD, and battery-powered portability.

Eclipse Tools Pro'sKit Mini-Soldering Stands: Compact, lightweight, and efficient. Includes 2 stands, iron holder, and sponge tray—perfect for precise, clean soldering.

Eclipse Tools Pro'sKit Twin Red Wire Ferrules: High-quality tin-plated copper ferrules for secure, efficient connections. Ideal for professionals and DIY enthusiasts. 500 pcs.

The Fluke i1010 is an AC/DC current clamp designed for use with digital multimeters. It measures currents from 1 A up to 1000 A DC and up to 600 A AC using a Hall-effect sensor. The clamp outputs 1 mV per amp for direct reading on compatible meters.

Fluke T130 voltage and continuity tester delivers reliable AC/DC testing from 6–690V with LCD display and switchable load, helping electricians verify live and dead circuits safely and clearly.

Fluke T+PRO-1AC combines a full-featured electrical tester with a non-contact AC voltage detector for safe AC/DC testing, continuity checks, GFCI testing, and fast live circuit detection.

Fluke BK120-107 kit combines a SmartTrace breaker finder and 107 pocket multimeter for fast circuit identification and everyday electrical troubleshooting.

Fluke FLK-FEV150/TY1 EV Charging Station Analyzer enables fast, safe AC EVSE testing with Type 1 connector, auto control pilot simulation, and guided workflows.

Fluke 28 II Digital Multimeter: Rugged, IP67 waterproof and dustproof, with true-RMS readings, high-accuracy voltage, current, and temperature measurements.

3 1/2 digits 1999 counts Dual slope A/D conversion Large backlit LCD display

Fluke 190-204-III is a 4-channel portable ScopeMeter oscilloscope with 200 MHz bandwidth, isolated inputs, WiFi and USB connectivity, built for high-voltage industrial signal troubleshooting.

Allen-Bradley 200-EX640Z1 instantaneous control relay with a 115–125VDC coil, designed for reliable multi-pole switching. Features 6 normally open and 4 normally closed contacts for industrial control logic.

Allen-Bradley 813S-V0WE line voltage monitor relay designed for three-phase systems to detect phase loss, phase reversal, and voltage unbalance, providing automatic protective signaling in motor control circuits.

Fluke PRV240FS provides a safe 240 V AC/DC source to verify FieldSense testers, multimeters, and clamp meters before and after live measurements.

Fluke 377 FC clamp meter delivers non-contact true-RMS AC/DC measurements with FieldSense, dual display, and 3-phase testing for fast, safe electrical diagnostics.

FThe Fluke 1507 is a compact, rugged insulation resistance tester offering selectable test voltages from 50 V to 1000 V, automatic Polarization Index (PI) and Dielectric Absorption Ratio (DAR) calculations, and CAT IV 600 V overvoltage rating — designed for contractors, industrial maintenance, and commissioning environments.

AEMC replacement set of 2 needle tip test leads, color-coded red/black with 4mm right-angle plugs. Rated 600V CAT IV shielded, fits meters 5212-5217.

Ensure safe, reliable electrical connections with Pro'sKit Insulated Yellow Wire Ferrules. 500 pcs of durable, tin-plated copper for lasting, high-quality performance.