Search results for: 'goods goods goods'

Fluke TP2 Slim-Reach test probe set includes one red and one black probe with 2 mm diameter stainless steel tips. Designed for probing closely spaced or recessed terminals, the probes are rated for 10 A and suitable for CAT III 1000 V and CAT IV 600 V environments.

Fluke TP220 industrial test probes include one red and one black probe with sharp stainless steel tips for reliable electrical contact. SureGrip overmolded handles and a flexible finger barrier support steady probe placement during measurement tasks. Designed for use with compatible Fluke test leads.

The Sprecher + Schuh D5-3T12 is a transformer element for D5 series 22 mm pilot devices. It converts a 480 V control voltage to a 6 V output for powering an incandescent lamp, allowing low-voltage lamp operation in high-voltage industrial control panels.

The REXA Koso S96111 Pulse Mod I/O Interface PCB Board is an internal electronic module used in REXA Electraulic™ actuators. It supports pulse modulation control and manages input and output signals within the actuator’s control system for precise positioning and communication.

The Schrack ZG400615 is a used ice cube relay rated for 5 Amps and up to 600 Volts. It features a 14-pin plug-in design and a 115 VAC coil voltage, making it suitable for general industrial control and electrical switching applications where reliable electromechanical control is required.

Fluke VPS410-II-R industrial voltage probe set delivers 500MHz bandwidth and 10:1 attenuation for accurate high-voltage signal measurement with compatible Fluke 190-II Series oscilloscopes.

Fluke 3PHVL-17XX-5M is a 3-phase + neutral voltage test lead cable assembly designed for structured multi-phase measurements, delivering organized lead management and reliable electrical connectivity over a 5 m length.

The Balluff BFO-48G-DSV-SC-1 is a glass fiber optic cable designed for use with a separate fiber optic base unit. It supports diffuse reflection sensing in side-view configurations and is suited for industrial detection tasks in harsh environments.

The Mitsubishi A1SG60 is a blank slot cover dummy module for MELSEC-A series PLC base units. It fills unused slots to protect internal components, reduce exposure to dust or foreign objects, and help maintain system stability when vacant slots are present.

The Molex 1300140037 is a 7-pole female circular connector pigtail designed for industrial electrical connections. It features a straight orientation, front panel mount configuration, and a 1/2-14 NPT mounting thread. The assembly is terminated with UL 1015 16 AWG lead wires and housed in a zinc die-cast body with black epoxy finish for durability.

ABB Steel City 72171 is a 4-11/16 in square steel electrical box with a 2-1/8 in depth and 42 cu in capacity. Constructed from pre-galvanized steel, it features eccentric knockouts for 1/2 in and 3/4 in conduit and is designed for commercial conduit wiring installations.

The Raco 3543-8 is a 3/4 in. 90 degree liquidtight connector with an insulated throat, designed for use with flexible metallic and Type B flexible nonmetallic liquidtight conduit in wet locations. Constructed from zinc-electroplated steel/malleable iron for corrosion protection.

Amprobe DL248D Deluxe Test Lead Kit delivers silicone 48-inch leads with interchangeable probes, clips, and lugs for reliable electrical testing and diagnostic flexibility across compatible measurement instruments.

Fluke TP81 insulation piercing probes provide controlled wire access through insulation using stainless steel needles and 4 mm banana jack compatibility for accurate automotive and electrical diagnostics.

Amprobe DL243D Basic Test Lead Kit delivers flexible silicone leads, probe tips, alligator clips, and spade lugs for reliable electrical testing with compatible test instruments.

Fluke Networks REMOTEID-1 Replacement Remote ID wiremapper enables accurate Ethernet cable identification and wire mapping when used with LinkIQ Cable+Network Testers.

Fluke TP80 electronic test probes provide insulated IC-safe probing for dense circuit boards. Designed for use with Fluke TL222 and TL224 leads, offering controlled access to compact electronic test points.

The Honeywell 620-0088 Parallel Link Driver Module is a communication module for the Honeywell IPC 620 PLC system. It supports parallel data transfer between compatible IPC 620 processors and connected system components and is used within industrial control, communication, and monitoring architectures.

The Gates 32CFHS G60899-0032 is a Code 61 SAE J518 split flange set used in high-pressure hydraulic systems. It is designed to connect ports directly to hoses and resist shock loads and vibration. The set includes two flange halves, an O-ring, and Grade 8 mounting hardware.

ABB TB806 Bus Inlet is a Modulebus extension cable adaptor with a D-sub 25 male connector. It is used with the TK801 extension cable to extend the ModuleBus in ABB S800 I/O systems. One adaptor is required per extension cable.

Honeywell 511-96019-101 Process Network Interface Module enables reliable communication within Honeywell TDC 3000 and Experion PKS distributed control systems, supporting Process Manager I/O network integration.

Fluke Networks 10220101 is a 6-wire in-line modular adapter with K-Plug, designed for safe circuit access and line testing on active telephone networks without interrupting service.

Fluke C35 soft carrying case protects compatible Fluke digital multimeters with durable 600D polyester construction and a lateral-opening design that allows in-case tool operation.

The Fluke AC285 SureGrip™ Alligator Clips include one red and one black large alligator clip with nickel-plated steel jaws. Designed with rubber overmolded SureGrip surfaces, they provide a stable, comfortable grip for electrical testing. Rated CAT IV 600 V, CAT III 1000 V, 10 A.

The Fluke TP88 Rigid Back Probe Pin Set includes two fine-tip, rigid back probe pins designed for use with 2 mm test probes. The red and black insulated pins slide onto compatible probes and allow access between weather pack seals and wires. Tested to 60 V DC.