Search results for: 'periodo'

Emerson DeltaV KJ3001X1-BD1 discrete input module for 120 VAC dry contact monitoring. This 8-channel module provides front-panel status indication and installs on DeltaV I/O hardware.

Minebea NMB-MAT 4715KL-05T-B40 is a 24V DC axial cooling fan with 119 x 119 x 38.4 mm dimensions, 3200 RPM speed, and approximately 118 CFM airflow for industrial equipment cooling.

Fisher 203-655-60-00 Big Foot Microphone for XLT30. High-sensitivity ground sensor for hard surfaces, enhancing contact and reducing noise to accurately detect underground water leaks.

The INNO Instrument CG-24 Cooling Tray is a standard accessory designed for the INNO Instrument A3 Fusion Splicer. It provides a dedicated, heat-resistant surface for fiber optic protection sleeves immediately after oven heating.

Fisher XLT-100 Compact Acoustic Leak Detector delivers precision underground water leak detection with adjustable frequency filters, 50/60Hz notch filtering, LCD signal display, and extension rods for extended reach.

The INNO Instrument JS-1500 is a 12V DC AC power adapter and charger designed for INNO thermal strippers including the TS-PRO and TS-PLUS. It provides stable DC output for heater operation while recharging the internal battery.

The GE Fanuc IC693CHS392G is a 10-slot expansion I/O baseplate for the Series 90-30 PLC platform. It features a 25-pin D-type expansion connector, rack address DIP switch, and supports local I/O expansion up to 50 feet. Designed for use with compatible CPU baseplates.

The Emerson KL2101X1-BA1 CHARM I/O Card (CIOC) is a DeltaV™ Electronic Marshalling subsystem component designed for industrial automation environments. It supports hazardous area installations and operates within -40 °C to +70 °C ambient conditions per manufacturer documentation.

The Struthers-Dunn W88AHPX-36 is a hermetically sealed 3PDT plug-in relay from the 88HP Series, rated 10A and configured for 120VAC operation. It features an 11-pin octal base and a sealed gray metal enclosure designed to prevent contamination and corrosion.

The INNO Instrument LBT-8 is an 880mAh lithium-ion replacement battery designed for INNO TS Plus (TSP-0002 / TS-8+) and TS Pro thermal fiber strippers. It supports approximately 500 stripping cycles of standard 12-fiber ribbon cable in SAVE mode when fully charged. This listing includes the battery only.

The INNO Instrument UN1CO Shoulder Strap is an accessory component for the UN1CO mobile workstation system. Designed for integration with the UN1CO work tray, it supports hands-free transport and stabilization of fiber optic splicing equipment during field deployment. This listing includes the shoulder strap only.

Fluke Networks CFM-TRC-S-MPO24P CertiFiber™ Max Test Reference Cord Set is designed for testing single-mode MPO 24 unpinned cables. The set includes one main and one remote reference cord and supports standards-preferred one-jumper reference methods when used with the CertiFiber™ Max Optical Loss Test Set.

Fluke FLUKE-CV401 is a 4 in (95 mm) ClirVu® infrared window with security key door latch for electrical inspection applications. It features AutoGround™ integrated grounding, IP67 environmental protection, and arc testing to 63 kA per IEEE C37.20.7 at KEMA.

The Appleton ST-4575 is a 3/4" 45° liquidtight connector designed for use with liquidtight flexible metal conduit (LFMC). This ST Series plain throat fitting provides a dependable connection while sealing out oil, water, dust, dirt, and fumes. Constructed with a malleable iron body and finished with zinc electroplate, chromate, and epoxy powder coat, it is suitable for wet locations and Class I, Division 2 environments.

The Fluke Networks DSX-CHA003 DSX Series Coaxial Adapter is designed for use with the DSX-5000 CableAnalyzer to characterize installed coaxial cabling. It supports testing of 50 ohm, 75 ohm, and 93 ohm coaxial cable and enables insertion loss measurements over a frequency range of 5 to 1002 MHz in accordance with applicable test limits.

The Fluke CV300 is a 75 mm ClirVu® infrared window with a hand turn door latch, designed to improve electrical inspection safety. It enables thermal inspections without opening energized panels and supports fast single-hole installation while maintaining enclosure ratings.

The Dwyer AP-7021-153-39 is a diaphragm operated pressure switch with an adjustable 10 to 125 psig range. It uses an SPDT snap acting switch in a general-purpose enclosure and is designed for air, non-corrosive gases, or compatible liquids.

Fluke TRC-SM-VERIFY-MPO24U is a reference-grade single-mode MPO 24 verification cord for CertiFiber™ Max testing, ensuring accurate reference setup when testing unpinned MPO fiber links.

The Allen-Bradley AK-R2-360P500 Dynamic Brake Resistor is an external medium-duty resistor kit designed for PowerFlex 70 and 700 series drives. It provides 360 ohms of resistance with an 86 watt continuous power rating to dissipate regenerative energy during motor braking.

The KAMAN Sensors digiVIT 855949-000 is a self-tuning digital driver for non-contact inductive and eddy current position and displacement sensors. It features pushbutton calibration, embedded intelligence, selectable analog outputs, and Ethernet connectivity for monitoring and parameter switching.

The Edwards Signaling 48XBRMG120A is a green LED visual signal light designed for indoor and outdoor industrial applications. Operating on 120 VAC, this dual-mode beacon supports steady-on or flashing operation and is housed in a corrosion-resistant NEMA 4X enclosure.

Schneider Modicon AS-W808-002 remote I/O signal and power cable enables communication and auxiliary power between Modicon 984 and 800 Series PLC processors and remote terminal bases in legacy automation systems.

Turck NI10-G18SK-RZ3X2 55MM inductive proximity sensor with 10 mm rated switching distance. Non-flush M18 threaded design with chrome-plated brass housing. Supports 20–250 VAC or 10–300 VDC operation using a 2-wire NC output. Terminal chamber connection with IP67 protection.

The Phoenix Contact RAD-ISM-900-XD-BUS is an OMNEX industrial wireless transceiver module operating in the 900 MHz ISM band. It supports bidirectional wireless transmission of digital and analog I/O signals and mounts on a DIN rail with an integrated bus foot for I/O expansion.