Search results for: 'installed'

SKF CMSS65-010-00-12-10 is a CMSS 65 series 5 mm eddy current probe with armored cable, 1/4-28 threaded fully threaded case, 3.0 cm case length, and 1.0 m overall length.

Eagle Eye HGD-2000-C3 Control Box with 3 Sensors Compatible with HGD-2000 for monitoring hydrogen gas buildup in battery rooms and similar facilities. Features dual relays, audible alarm, and AC power input.

The INNO Instrument E-70 fusion splicer electrodes are official replacement components designed for compatibility with INNO View Pro, Ribbon, and X Series splice machines. Rated for up to 5,500 splices per set, they support stable arc discharge performance and scheduled maintenance intervals.

The Siemens 3TX4422-0A SIRIUS auxiliary contact block features 2NO + 2NC instantaneous contacts with screw-type terminals. Designed for use with contactor relays and power contactors according to EN 50011, it supports snap-on mounting, IP20 front protection, and positively driven operation per IEC 60947-5-1.

The INNO Instrument FFLBT-50 is a rechargeable 11.1V lithium-ion battery pack rated at 3800mAh (42.18Wh). Designed for use with compatible INNO fusion splicers, it provides field-replaceable power in a compact integrated housing with built-in charge indicator.

Siemens 771-8STF1 current-to-pneumatic (I/P) transducer converts a DC mA input to a proportional pneumatic output. Configuration: 4–20 mA input, 3–27 psig output, standard output capacity, terminal strip, intrinsically safe approval.

The INNO Instrument DIN-18 is a DC power cable designed to connect compatible INNO TS-Pro or TS-Plus thermal strippers to the power output port of supported INNO View series fusion splicers. It enables field operation by allowing the thermal stripper to draw power directly from the splicer’s internal battery.

Fluke Networks CFM-TRC-S-MPO24P CertiFiber™ Max Test Reference Cord Set is designed for testing single-mode MPO 24 unpinned cables. The set includes one main and one remote reference cord and supports standards-preferred one-jumper reference methods when used with the CertiFiber™ Max Optical Loss Test Set.

Fluke Networks CFM-TRC-S-MPO24U CertiFiber™ Max Test Reference Cord Set for testing single-mode MPO 24 pinned cables. Includes one main and one remote reference cord. Designed for use with the CertiFiber™ Max Optical Loss Test Set and supports standards-preferred one-jumper reference method.

The Fluke I17XX-FLEX3000/4PK includes four 24 in iFlex® flexible AC current probes rated to 3000 A AC. Designed for use with Fluke 17XX Energy and Power Loggers, these Rogowski-style probes connect directly to the instrument and feature 1.8 m output cables for measurement flexibility.

The Siemens TA2J6500 is an aluminum body 2-barrel lug accessory for use with 2- or 3-pole 200A–400A JD and LD frame molded case circuit breakers. It supports copper conductors from 3/0 AWG to 500 kcmil and aluminum conductors from 4/0 AWG to 500 kcmil, and is suitable for both line and load side connections.

The INNO Instrument DC300A Flat Cable Stripper is an aluminum stripping tool designed for 3 × 2 mm flat drop cable, 900 µm coating fiber, and 250 µm coating fiber. It features three side blades and an integrated locating ruler for consistent cleaver length positioning. 

Fluke Networks CFM-TRC-S-MPO16P is a CertiFiber™ Max single-mode test reference cord kit designed for testing MPO16 unpinned fiber cables. The kit includes main and remote reference cords and supports standards-preferred one-jumper reference methods when used with the CertiFiber Max Optical Loss Test Set.

The Fluke i1010 AC/DC current clamp kit extends the current measurement range of compatible multimeters. It measures AC current from 1 A to 600 A and DC current from 1 A to 1000 A using a Hall-effect sensor. The kit includes a zippered carrying case for storage and transport.

Fluke i17XX-FLEX3000 flexible iFlex current clamp measures up to 3000A AC and connects directly to Fluke 17XX Energy and Power Loggers, delivering accurate high-current measurement in tight spaces.

The Hammond Power CRX06D1BC is a three-phase iron core line reactor rated for 600 VAC and 6.1 A. Part of the HPS Centurion® R Series, it provides controlled impedance to mitigate harmonics and electrical transients in AC drive systems operating at 50/60 Hz.

Banner Engineering IAT210S glass fiber optic sensor cable with diffuse-reflective sensing. Features a right-angle brass sensing end, stainless steel monocoil sheathing, 3.2 mm glass fiber core, and 4.572 m length. Designed for use with a separate fiber optic amplifier.

Fluke T150 two-pole voltage and continuity tester delivers fast AC/DC measurements from 6–690V with backlit LCD, switchable load, resistance testing, and multi-mode voltage indication for electrical diagnostics.

Fluke T130 voltage and continuity tester delivers reliable AC/DC testing from 6–690V with LCD display and switchable load, helping electricians verify live and dead circuits safely and clearly.

The Siemens 3SU1400-1AA10-1BA0 is a SIRIUS ACT contact module with one normally open contact. It features screw terminals and a snap-on design for front plate mounting behind compatible actuators. Designed for industrial control and signaling applications requiring reliable signal switching.

The GE DS200VPBLG1AFF is a VME P2 backplane board used in GE LS2100 and Load Commutated Inverter control systems. It provides centralized power and signal distribution across a 13-slot chassis, supporting DSPC, gate distribution, exciter, and I/O extender boards.

The ABB Bailey IMASI02 is an Analog Slave Input module for the Infi 90 Process Management System. It converts analog field signals into digital data for processing by a Multi-Function Processor and interfaces up to fifteen process signals through a single MMU slot.

The ABB Bailey IMFCS01 is an intelligent Frequency Counter Slave Module for INFI 90 and Net 90 DCS platforms. It processes high-speed pulse inputs from field sensors and communicates frequency and period data to a Multi-Function Processor via the slave expander bus for speed monitoring and control.

Fluke Networks NFC-SWABS-1.25MM fiber optic cleaning swabs are designed for LC and MU ports, delivering precise 1.25mm bulkhead cleaning with lint-free material for effective wet or dry connector maintenance.