Search results for: 'connects'

GE C208LSIR MicroVersaTrip Plus Trip Unit delivers replacement circuit breaker trip control with front-panel setup access, status display, and 800A sensor designation for compatible GE breaker systems.

Bently Nevada 330101-00-80-05-02-00 3300 XL 8mm Probe built for vibration sensing in 3300 XL monitoring setups, with attached cable and connector shown in the provided images.

INNO Instrument PAC-1007 small alligator adapter pair with safety connector, rated 300V CAT II 15A, in red and black.

Fisher HANDLEKIT-TW6 3-piece kit converts TW6 into a two-box metal detector for blind search. Couples transmitter and receiver for single-user tracing of underground pipes, cables, and buried metal objects.

Siemens 771-8STF1 current-to-pneumatic (I/P) transducer converts a DC mA input to a proportional pneumatic output. Configuration: 4–20 mA input, 3–27 psig output, standard output capacity, terminal strip, intrinsically safe approval.

Fluke Networks NFA-MMC24U-KIT UniPort Adapter Kit is designed for testing MMC 24 unpinned single-mode or multimode fiber cables with the CertiFiber™ Max Optical Loss Test Set. The kit includes pinned UniPort adapters and supporting components for fiber loss, length, and polarity measurement applications.

The Siemens TA2J6500 is an aluminum body 2-barrel lug accessory for use with 2- or 3-pole 200A–400A JD and LD frame molded case circuit breakers. It supports copper conductors from 3/0 AWG to 500 kcmil and aluminum conductors from 4/0 AWG to 500 kcmil, and is suitable for both line and load side connections.

The KAMAN Sensors digiVIT 855949-000 is a self-tuning digital driver for non-contact inductive and eddy current position and displacement sensors. It features pushbutton calibration, embedded intelligence, selectable analog outputs, and Ethernet connectivity for monitoring and parameter switching.

Pomona 5523 Minigrabber Patch Cord Kit includes ten 24-inch 20 AWG test leads with gold-plated minigrabber clips, providing secure temporary jumper connections for terminals and wire-wrap posts.

Honeywell 380-01873-100 I/O Interface Module enables remote monitoring and control of field devices using RS485 Panel Bus™ communication with 34 configurable I/O points for scalable building automation systems.

The Square D 8501NR61 is an 11-pin plug-in relay socket designed for use with compatible Square D relays and timers. It features single-tier screw clamp terminals and supports both panel and DIN rail mounting for industrial control applications.

The Allen-Bradley 800T-XA2 Series D is a 30 mm industrial control contact block featuring two normally open contacts and an A600 NEMA pilot duty rating. Designed for use with Bulletin 800T operators, it provides screw-terminal connections and base-mount installation for industrial control panels.

Fluke 1555 FC KIT insulation resistance tester delivers digital testing up to 10 kV with IR3000FC wireless connectivity, onboard data storage, and advanced diagnostic measurements for high-voltage electrical assets.

Fluke 190-104-III-S portable ScopeMeter oscilloscope delivers 100 MHz bandwidth, four isolated channels, and rugged field performance for industrial waveform analysis and troubleshooting.

Fluke 190-204-III is a 4-channel portable ScopeMeter oscilloscope with 200 MHz bandwidth, isolated inputs, WiFi and USB connectivity, built for high-voltage industrial signal troubleshooting.

Fluke SOL-DMM87V-KIT combines a high-efficiency PV I-V curve tracer with an 87V multimeter and 393 FC clamp meter for solar diagnostics.

Fluke ii905 Acoustic Imager detects and quantifies gas and vacuum leaks up to 70 m with LeakQ leak rate and cost estimation plus Wi-Fi sharing.

100MHz, 2-channel portable oscilloscope performance with CAT IV safety, deep memory, and Connect-and-View triggering.

Fluke I2500-18 flexible AC current probe enables accurate 2500A measurements with thin Rogowski coil design for tight spaces and hard-to-reach conductors.

Allen-Bradley 800H-R3HA7 explosion-proof selector switch station with HAND-OFF-AUTO operation, built in a Type 7 & 9 aluminum enclosure for Class I, II, and III hazardous industrial locations.

Fluke 1773/BASIC analyzer delivers automated three-phase power quality testing with fast transient capture, harmonic analysis, and flexible USB/Ethernet data transfer.

Fluke TL238 test lead kit enhances safety in high-energy environments with insulated probes, extenders, and silicone leads for secure multimeter connections.

Fluke Networks SMC-9-SCST launch cable delivers 160m singlemode fiber for accurate OTDR testing, stable network connectivity, and compatibility with OptiFiber units.

Fluke 190-504-III ScopeMeter: Rugged 500MHz, 4-channel portable oscilloscope with deep memory, USB/Wi-Fi, and CAT IV 600V safety rating.