Search results for: 'motor used'

Allen-Bradley 1336-R2-SP2A precharge resistor kit for 1336 series drives, providing safe inrush current control and reliable compatibility across multiple drive families.

INNO Instrument SPA1000 digital power meter with 1 power channel, AC/DC measurement, 100 kHz bandwidth, up to 1000 V and 20 A input, 4-item LED display, and harmonic measurement to the 100th order.

Easy-Laser Case 3 shim kit with Types A/B/C/D, 0.05–2.00 mm stainless steel shims, permanently marked and burr-free. Foam-organized case for precise machine alignment setups.

Crydom Crouzet DR-ODC5 relay delivers fast, isolated DC load switching with a 5V control signal, DIN-rail mounting, and an LED indicator for industrial automation.

AEMC 6527 Digital Megohmmeter: Multi-range insulation and continuity tester with voltmeter, audible alerts, and lockable test button for field use.

Allen-Bradley 100-D-S1-11 auxiliary contact block adds 1NO/1NC control contacts to 100-D series contactors, offering reliable screw-terminal expansion for industrial panels.

Fluke FLUKE-355 Clamp Meter: High-current True-RMS AC/DC measurements up to 2000A with wide jaw capacity, surge capture, and CAT IV safety for demanding electrical work.

The Functional Devices RIB2401B is a 20 Amp SPDT power control relay with a continuous duty coil and multi-voltage input of 24 Vac/dc or 120 Vac, 50–60 Hz. Housed in a NEMA 1 enclosure accepted for plenum use, it includes a visible LED status indicator and 16-inch 600V rated lead wires. The relay supports general purpose, ballast, pilot duty, tungsten, and motor loads within its published ratings.

Wohler VIS 750 is a complete HD inspection camera system in a clean, portable trolley. Includes a 7" monitor, an HD pan & tilt camera head with motorized focus, and a 130’ or 200’ push rod, built for long pipe runs and cleaner transport.

Eaton XTCEXSAB10 adds a reliable 1NO auxiliary contact to XTCE Frame B contactors, enhancing XT Series control systems with safe, compact side-mount functionality.

The MDI 35NO-120A mercury displacement contactor delivers silent, durable 35A switching with a 120V coil, ideal for resistive loads and industrial control systems.

Complete Pruftechnik ROTALIGN Ultra kit with Shaft Alignment Advanced license, ROTALIGN sensor and laser, Bluetooth module, chain and magnetic bracket sets, cables, software, and ABS transport case.

Agastat 7014SC delivers reliable 2–20s on-delay timing with 4PDT contacts for industrial automation, offering durable electropneumatic performance and high repeatability.

Commtest vb7 vibration data collector for route-based machinery vibration measurement, spectrum and waveform analysis, balancing, and condition monitoring with firmware v2.1.8 and IMI ICP accelerometers.

The Fluke 810 Vibration Tester is a handheld diagnostic instrument for identifying mechanical vibration faults in rotating equipment. Using tri-axial measurement and on-device analysis, it reports fault type, location, and severity during field testing.

Allen-Bradley SP-140550 bus capacitor kit for Bulletin 1336 AC drives. Designed for 460 VAC systems in the 75–200 HP range, this mountable component supports stable DC bus operation.

The ABB 1SVR430841R0200 CM-SRS.11 provides TRMS current monitoring with adjustable thresholds and multiple ranges, ideal for single-phase industrial control protection.

The Mitsubishi CP30-BA 1-Pole 3A M-Curve Circuit Protector is a compact hydraulic-magnetic supplementary protector designed for low-capacity control circuits. It supports AC 250 V and DC 65 V operation, offers 2.5 kA breaking capacity, and mounts on standard DIN rail using screw terminals.