Search results for: 'box'

Square D 2510KG1 manual switch delivers reliable 30A control for single-phase systems with a 2-pole toggle design and non-reversing operation in a compact NEMA 1 enclosure.

SKF CMSS65-010-00-12-10 is a CMSS 65 series 5 mm eddy current probe with armored cable, 1/4-28 threaded fully threaded case, 3.0 cm case length, and 1.0 m overall length.

The ABB OHDI-01 is a 115/230 VAC digital input module designed for use with ABB ACS550, ACH550, and ACS800 drives. It converts high-voltage digital input signals to 24 VDC drive inputs and supports up to six 115 VAC inputs or three 230 VAC inputs.

Fisher M101 rebar locator with 4.5 kHz Double D coil delivers precise concrete scanning to locate reinforcing bar, conduit, and embedded metal with meter and audio indication.

Siemens 771-8STF1 current-to-pneumatic (I/P) transducer converts a DC mA input to a proportional pneumatic output. Configuration: 4–20 mA input, 3–27 psig output, standard output capacity, terminal strip, intrinsically safe approval.

The General Electric CR104PLT43 is a 30.5mm push-to-test indicator light designed for 240V AC industrial automation systems. Part of the GE CR104P series, it utilizes a resistor power supply and supports machine-tool and control panel applications where manual lamp verification is required.

The GE Fanuc IC693CHS392G is a 10-slot expansion I/O baseplate for the Series 90-30 PLC platform. It features a 25-pin D-type expansion connector, rack address DIP switch, and supports local I/O expansion up to 50 feet. Designed for use with compatible CPU baseplates.

The Delta AFB1224HE is a 24V DC brushless axial cooling fan designed for reliable airflow in electronic and industrial equipment. It features dual ball bearings, locked rotor protection, and a 120 × 120 × 38 mm frame for consistent thermal management applications.

The Universal 447-LR-TC-P is a 120V magnetic fluorescent ballast designed to operate two lamps in trigger-start configurations. It supports F20T12, F15T8, and F15T12 lamps and features a low power factor, lag-type circuit. UL and CSA certifications support indoor and Type 1 outdoor use.

The Eaton H2006B-3 is a Freedom NEMA heater coil set designed for thermal overload protection in motor control applications. This Class 20 standard trip heater pack supports selectable full load current settings from 1.79A to 2.9A via dial positions A–D and is supplied as a factory-calibrated set of three elements.

The Omron MY4Z DC24(S) is a general-purpose miniature power relay with a 4PDT contact configuration and 24 VDC coil. Rated for 5 A switching in four-pole applications, it is designed for sequence control and power switching in industrial control systems.

The Allen-Bradley AK-R2-360P500 Dynamic Brake Resistor is an external medium-duty resistor kit designed for PowerFlex 70 and 700 series drives. It provides 360 ohms of resistance with an 86 watt continuous power rating to dissipate regenerative energy during motor braking.

The KAMAN Sensors digiVIT 855949-000 is a self-tuning digital driver for non-contact inductive and eddy current position and displacement sensors. It features pushbutton calibration, embedded intelligence, selectable analog outputs, and Ethernet connectivity for monitoring and parameter switching.

The MIP LM 3086 EPA3 is a laser-based opacity and dust monitor designed for continuous emissions monitoring in industrial stacks. It uses a single-pass, dual-path laser architecture with an optical reference path to measure opacity, optical density, and calibrated dust concentration values.

Honeywell 380-01873-100 I/O Interface Module enables remote monitoring and control of field devices using RS485 Panel Bus™ communication with 34 configurable I/O points for scalable building automation systems.

The General Electric DS200DDTBG2ABB is an LCI Auxiliary I/O Terminal Board for GE Mark V Speedtronic gas and steam turbine control systems. It provides auxiliary signal termination, conditioning, and isolation for analog and digital I/O in high-voltage industrial control environments.

This CCC Series 4 temperature input module set includes one IOM TCW (I-1/201-2/200) and one EIOM TCW (E-1/202-3/200). Both modules are designed for 3-wire GDC RTD temperature inputs and chassis mounting within CCC Series 4 control systems.

The Square D 8501NR61 is an 11-pin plug-in relay socket designed for use with compatible Square D relays and timers. It features single-tier screw clamp terminals and supports both panel and DIN rail mounting for industrial control applications.

The Allen-Bradley 800T-XA2 Series D is a 30 mm industrial control contact block featuring two normally open contacts and an A600 NEMA pilot duty rating. Designed for use with Bulletin 800T operators, it provides screw-terminal connections and base-mount installation for industrial control panels.

Allen-Bradley 200-EX640Z1 instantaneous control relay with a 115–125VDC coil, designed for reliable multi-pole switching. Features 6 normally open and 4 normally closed contacts for industrial control logic.

Allen-Bradley 813S-V0WE line voltage monitor relay designed for three-phase systems to detect phase loss, phase reversal, and voltage unbalance, providing automatic protective signaling in motor control circuits.

Allen-Bradley 1336-RLOAD-SP2A load resistor module engineered for 1336 PLUS, PLUS II, FORCE, and IMPACT drives, providing controlled regenerative and braking energy dissipation in supported voltage ranges.

Allen-Bradley 1336-RLOAD-SP5A load resistor designed for 1336 adjustable frequency drives. Supports 575V operation in Frame E systems rated 150–300 HP for controlled load management.

Allen-Bradley 1336-T-SP5A control transformer designed for 1336 PLUS, PLUS II, Force, and Impact drives, supporting 150–250 HP systems at 460 VAC with stable internal control power delivery.