Search results for: 'new tist'

Fluke FEV100/TY1 & TSL kit tests Type 1 and Tesla AC EV chargers with EV simulation, GFCI checks, grounding pre-tests, and full EVSE safety verification.

Fluke Networks NFA-E2K-SINGLE E2000 interchangeable adapter enables accurate optical power testing when used with compatible CFP power meters.

Fluke TP912 replacement tips provide multiple stainless steel and gold-plated contact styles for TL910 electronic test probes, enabling precise electrical measurements across varied probing conditions.

Fluke Networks TRC-SM-VERIFY-MMC16U is a reference-grade single-mode verification test reference cord for CertiFiber™ Max optical loss testing. It is a 1 m, 16-fiber, Type A MMC cord with APC/U connectors, used to verify proper reference setup accuracy.

Fluke FEV150 EV Charging Station Analyzer performs guided safety and performance testing of AC EV chargers with Type 1 and Tesla plugs.

Fluke TL1500DC test leads provide safe, accurate voltage measurements up to 1500 V DC, ideal for multimeters, clamp meters, and solar/battery testing.

Fluke TL960 test leads with micro-hooks for precise component connections, 90 cm PVC insulation, 4 mm banana plugs, safe for low-voltage applications.

The AEMC 2129.87 Kelvin Lead Set provides 50 ft color-coded Kelvin connections with 3 in C-clamps for low-resistance measurement applications using compatible AEMC 6290 and 6292 micro-ohmmeters.

Pomona 1325-0 solderless stackable banana plugs feature set-screw assembly, gold-plated connector body, and support 22–18 AWG wire for custom leads.

AEMC 2129.89 Kelvin Lead Set provides 20 ft color-coded Kelvin connections with 3 in C-clamps for low-resistance testing applications using compatible AEMC 6290 and 6292 micro-ohmmeters.

The Fluke TL222 SureGrip test lead set includes red and black silicone-insulated leads with right angle connectors on both ends. Designed for digital multimeters, these leads feature safety-shrouded banana plugs, reinforced strain relief, and a 1.5 meter cable rated for CAT IV 600 V and CAT III 1000 V applications.

The Fluke Networks TS52 PRO (52801001) is a telephone-test set that combines a back-lit LCD, glow-in-the-dark keypad and DataSafe Pro high-impedance monitoring with piercing-pin clip connectors—ideal for rugged outside-plant voice/data line work.

Fluke 1555 FC insulation tester delivers up to 10 kV testing with Fluke Connect remote operation, PI/DAR calculations, and CAT IV safety ratings.

The Fluke Networks TS25D (model 25501009) telephone test set features Angled Bed-of-Nails (ABN) clip connectors, high-impedance monitor mode, DSL/POTS filter, caller-ID and tone-generator support—designed for technicians in telecom line installation and maintenance.

AEMC 2135.79 Replacement Black Extension Lead provides a 5 m connection solution for Model 6474 and compatible test equipment using 4 mm safety banana plug interfaces.

The Fluke TP88 Rigid Back Probe Pin Set includes two fine-tip, rigid back probe pins designed for use with 2 mm test probes. The red and black insulated pins slide onto compatible probes and allow access between weather pack seals and wires. Tested to 60 V DC.

Pomona 2631 BNC Female to Minigator Test Clips breakout cable enables fast signal access from BNC male cables to minigator clips for bench and handheld electronic testing applications.

Pomona 6365 replacement DMM test lead set designed for sheathed banana jack multimeters. CAT III 1000V rated with silicone wire and molded probe bodies for reliable electrical testing.

Fluke Networks P4480RJ9 replacement line cord features RJ11 to angled bed-of-nails clips, delivering clear voice quality for TS52, TS44, and TS42 test sets.

The Fluke 1587T Insulation Multimeter combines a digital insulation tester with a true-rms digital multimeter in one handheld instrument. Designed for telecom applications, it provides 50 V and 100 V insulation test voltages along with AC/DC voltage, millivolt, milliamp, resistance, and continuity measurements.

The Fluke Networks NFA-MPO12U-KIT is a UniPort™ adapter kit designed for testing MPO12 unpinned fiber cables with the CertiFiber™ Max Optical Loss Test Set. It includes two field-replaceable UniPort adapters that support single-mode or multimode testing and enable standards-preferred one-jumper reference measurements.

Fluke TP165X probe lets you test hard-to-reach points safely with a slim design and convenient test button for precise control.

Fluke Networks Electrical Contractor Telecom Kit I: Durable telecom tool kit with TS30 test set for installation, testing, and troubleshooting.

Pomona 5523 Minigrabber Patch Cord Kit includes ten 24-inch 20 AWG test leads with gold-plated minigrabber clips, providing secure temporary jumper connections for terminals and wire-wrap posts.