Search results for: '200 4'

Delivers fast point-to-point continuity testing for grounded pathways and long-distance connections with polarity reversal, lead compensation, programmable thresholds, and 300 V CAT IV safety.

Fluke 190-204-III is a 4-channel portable ScopeMeter oscilloscope with 200 MHz bandwidth, isolated inputs, WiFi and USB connectivity, built for high-voltage industrial signal troubleshooting.

Fluke 190-204-III CAL ScopeMeter offers 200 MHz bandwidth, four isolated channels, deep memory, and traceable calibration for advanced industrial troubleshooting.

Fluke T6-1000PRO electrical tester uses FieldSense technology to measure true RMS AC voltage and current up to 1000V and 200A through an open fork for faster, safer troubleshooting.

LEM USA HAL 200-S Current Transducer: Precision 200A Hall Effect sensing for industrial power systems. Compact, efficient, and high immunity to interference!

Fluke i200 AC current clamp enables accurate 0.5–200A AC measurements using a multimeter. Features 1 mA/A output, banana plug interface, and CAT III 600V safety for electrical testing.

Fluke i200S AC Current Clamp delivers accurate non-intrusive AC current measurement from 0.5A to 240A using a BNC voltage output, ideal for multimeters, oscilloscopes, and power quality tools.

The Fluke 87V/PRV240 Digital Multimeter Kit combines the Fluke 87V Industrial Digital Multimeter with the PRV240 Proving Unit. The 87V supports AC/DC voltage and current measurement up to 1000 V and 10 A, resistance to 50 MΩ, capacitance, frequency to 200 kHz, and temperature from -200°C to 1090°C. The PRV240 provides a portable 240 V AC/DC source for verifying proper meter operation before testing.

AEMC 6292 Micro-Ohmmeter: Portable low-resistance tester with 200A current, precise measurement, and DataView software for efficient reporting.

3 1/2 digits 1999 counts Dual slope A/D conversion Large backlit LCD display

Fluke Networks IntelliTone MT-8203-20 test leads with bed-of-nails clips ensure secure signal tracing and precise wire piercing for Pro 100/200 tools.

AEMC LM103 AC Current Probe, 200A range, 1mV/A output, 5 ft lead with banana plugs, 48 Hz–10 kHz frequency, compatible with power analyzers & DMMs.

Amprobe 30XR-A Multimeter: Accurate voltage, current, and resistance testing with VolTect non-contact detection, data hold, and manual ranging.

AEMC MN94 AC Current Probe: Compact 200A sensor with 4-pin lead, 0.2 class accuracy—ideal for PowerPad 8345 & PEL52, meter checks, and power analysis.

AEMC MN291 AC Current Probe: 200A range, 100mVDC/A output for DMMs or loggers, compact design with banana plug lead, ideal for DC voltage input instruments.

The AEMC 2150.20 is a portable, battery-powered instrument that combines a 20 MHz two-channel isolated oscilloscope, dual 8000-count TRMS multimeter, power measurements, harmonic analysis (up to the 31st order), data storage, and USB connectivity for electrical diagnostics.

Fluke 365 Clamp Meter: True-RMS AC/DC measurement with detachable jaw, built-in flashlight, and rugged design for tight access environments.

The Fluke LIQ-KIT-87-5 Electrical & Network Troubleshooter Kit combines the LinkIQ Cable+Network Tester, IntelliTone Pro 200 probe, and Fluke 87V Industrial Multimeter in a single field-ready solution. It qualifies copper cabling up to 10GBASE-T using frequency-based measurements, performs switch and Ping diagnostics, and validates PoE negotiation and load delivery. The integrated multimeter supports electrical troubleshooting across industrial environments.

Fluke 435-II power quality and energy analyzer for Class A three-phase testing, with PowerWave capture, transient analysis, harmonics, flicker, mains signaling, energy loss measurement, and power distribution troubleshooting.

Compact AEMC MN379T AC Current Probe with True RMS, 5A & 100A ranges, 200mV/A & 10mV/A outputs, 10 ft BNC lead, 40 Hz–10 kHz frequency response.

AEMC LM102 AC Current Probe, 200A range, 1mA/A output, 5 ft lead with banana plugs, 48 Hz–10 kHz frequency, ideal for power analyzers and DMMs.