Search results for: 'Requirements'

Fluke TP38 probes offer slim insulated tips for safe access to tight terminals, featuring hardened stainless steel tips and CAT IV 600V safety rating.

Brady WML-0811-202 self-laminating B-292 vinyl labels deliver durable wire ID for legacy Brady printers, offering strong adhesion and reliable cable marking.

AEMC 2135.86 BNC 150 ft M/F Extension Lead provides extended BNC connectivity for compatible electrical testing and measurement equipment requiring male-to-female BNC cable extension capability.

AEMC 2135.76 BNC 50 ft (15 m) Extension Lead expands connection reach for Model 6474 and other compatible BNC-connected electrical testing equipment in field and industrial measurement environments.

AEMC 2135.75 replacement connection lead keeps compatible AEMC 6472 and 6474 electrical test setups ready with a direct-fit connection accessory.

Fluke TP220 industrial test probes include one red and one black probe with sharp stainless steel tips for reliable electrical contact. SureGrip overmolded handles and a flexible finger barrier support steady probe placement during measurement tasks. Designed for use with compatible Fluke test leads.

AEMC 2129.72 Kelvin Lead Set provides 25 ft Kelvin leads with 200A Hippo clamps for use with AEMC Model 6292 low-resistance testing applications requiring secure current and potential connections.

AEMC 2118.80 Kelvin Clips provide 20 ft test lead reach with 1-10A current capability for low-resistance measurement applications. Designed for use with compatible AEMC micro-ohmmeters.

HARTING 09150006206 silver-plated Han D female crimp contact with AWG 14 capability delivers reliable 10 A performance and low ≤3 mΩ resistance for industrial connector applications.

AEMC 2118.70 Kelvin Clips provide 20 ft color-coded 10A Hippo test leads with spade lug terminations for compatible micro-ohmmeter connections.

Eagle Eye IBEX 4-Point Test Leads for battery analyzers provide four-contact measurement for battery resistance and voltage testing with compatible IBEX systems.

AEMC 2129.95 RTD Temperature Probe provides temperature compensation capability for AEMC 6250 and 6255 testing systems, helping improve measurement accuracy during resistance testing where ambient temperature variations affect results.

Fluke TP2 Slim-Reach test probe set includes one red and one black probe with 2 mm diameter stainless steel tips. Designed for probing closely spaced or recessed terminals, the probes are rated for 10 A and suitable for CAT III 1000 V and CAT IV 600 V environments.

The Fluke TP88 Rigid Back Probe Pin Set includes two fine-tip, rigid back probe pins designed for use with 2 mm test probes. The red and black insulated pins slide onto compatible probes and allow access between weather pack seals and wires. Tested to 60 V DC.

Rohde & Schwarz FSH-Z1 true RMS terminating RF power sensor for 10 MHz–8 GHz measurements, providing accurate average power analysis and direct compatibility with FSH series handheld spectrum analyzers.

AEMC 2136.77 Replacement Lead Set provides 15 ft test leads designed for use with AEMC DTR Models 8500 and 8510. Supplied as a set of two leads and intended as a replacement for Cat #2118.48.

Fluke TL224 SureGrip insulated test leads include one red and one black lead with safety-shrouded standard diameter banana plugs. The leads feature a right-angle connector on one end and a straight connector on the other, reinforced strain relief, and silicone-insulated wire designed to resist heat and cold.

The Fluke TL75 Hard Point Test Lead Set combines test lead and probe into a single unit for general-purpose electrical measurements. This set includes one red and one black PVC-insulated lead, each 48 inches long, with right-angle shrouded banana plugs and removable protective caps.

Snap On MT2500-43 Short Test Lead Jumper: Essential tool for reliable diagnostics. Designed for precision and durability to enhance your testing efficiency.

AEMC 2129.89 Kelvin Lead Set provides 20 ft color-coded Kelvin connections with 3 in C-clamps for low-resistance testing applications using compatible AEMC 6290 and 6292 micro-ohmmeters.

Pomona 5953A adjustable tip test probe set includes one red and one black probe with retractable stainless steel needle tips adjustable from 0 to 3 inches. Designed with shrouded banana plugs and silicone-insulated leads, the set is rated CAT II 600 V and supports up to 3 A.

INNO Instrument PAL-1003 external sensor connection cable with BNC connector for connecting external CT or VT sensors to compatible INNO Instrument SPA series power analyzers.

AEMC 2118.78 Kelvin probes bring crisp 10A low-resistance test contact with spring-loaded rotating tips, 4-wire measurement support, and 20 ft leads.

Brady WML-311-292 labels offer durable, self-laminating wire ID for 10–6 AWG wires, using B-292 vinyl for clear, long-lasting identification with Brady printers.

IDEAL 85-346 Cat5e RJ45 Connector delivers reliable Ethernet cable termination for 24 AWG Cat5e cables, ideal for network installers using standard RJ45 crimp tools.