Search results for: 'it's for'

The Georg Fischer Signet 3-8510 is an integral-mount paddlewheel flow sensor designed for use in liquid flow measurement applications. This sensor is part of the GF Signet flow measurement platform and is intended for installation within compatible piping systems to generate a flow-proportional signal.

The Dwyer 1638-2 is a large diaphragm pressure switch designed for low-pressure applications with an operating range of 1 to 3 inches water column (WC). This configuration supports pressure-actuated switching within defined low differential ranges.

The AMLOC 120-4416 is a high-temperature capacitance sensor assembly used within AMLOC Energy Management Systems for desiccant air dryers. It interprets capacitance signals associated with moisture loading in the desiccant bed to support energy-managed dryer operation.

Commtest vb7 vibration data collector for route-based machinery vibration measurement, spectrum and waveform analysis, balancing, and condition monitoring with firmware v2.1.8 and IMI ICP accelerometers.

The Fluke 810 Vibration Tester is a handheld diagnostic instrument for identifying mechanical vibration faults in rotating equipment. Using tri-axial measurement and on-device analysis, it reports fault type, location, and severity during field testing.

Fluke MDA-550/FPC Motor Drive Analyzer: 4-channel, 500 MHz testing with guided setup, preset profiles, and built-in professional report generation.

Valco Melton 765XX125 Valve Module Assembly delivers controlled fluid actuation for industrial adhesive and dispensing systems, supporting precise flow regulation within automated production environments.

The Eagle Eye IBEX-Temperature Probe-IR is a temperature probe accessory designed for use with IBEX battery testing equipment. The probe connects via cable and supports temperature measurement during battery testing and diagnostic procedures.

AEMC 2126.46 K-Type Needle Thermocouple Probe brings needle-style temperature measurement to compatible AEMC data logging workflows, with a -58°F to 1292°F range.

Banner QS30EDVQ diffuse-mode photoelectric sensor with visible red 660 nm beam and bipolar NPN/PNP outputs offers fast response and reliable 1400 mm detection for industrial automation.

Honeywell 513-04476-175 analog output termination board delivers eight 4–20 mA outputs for precise field device control in Honeywell UCN and TDC 3000 systems with conformal-coated reliability.

The Yamatake Honeywell J-AOM10 is an analog output module designed for use within industrial control systems. The module operates on DC 24V power and features terminal screw connections for field wiring. It is labeled and manufactured under the Yamatake Honeywell brand.

Siemens SIMATIC S7 memory card for S7-400 systems. This long-design Flash-EPROM card provides 1 Mbyte of non-volatile storage for user programs and data. Designed for 5 V operation and manufactured in Germany for use with SIMATIC S7-400 automation platforms.

Fluke TLK282 Test Lead Kit: Deluxe SureGrip leads with back probe pins and hook clips, ideal for automotive diagnostics up to 60 V DC.

Banner LM3 photoelectric sensor logic module delivers ON-OFF logic with LIGHT/DARK operate selection for MULTI-BEAM 3- and 4-wire sensors.

Allen-Bradley 1336-CAP-SP3-A DC bus capacitor assembly designed for 460V 1336 PLUS, FORCE, and IMPACT drives. Supports stable DC bus operation in compatible 25–30 HP drive systems.

Allen-Bradley 1336-RLOAD-SP1A load resistor for Bulletin 1336 AC drives, designed to manage internal load, DC bus discharge, and power stabilization in 25–30 HP, 460V drive systems.

Allen-Bradley SP-122972 Feedback Board supports 1395 drive systems by processing drive feedback signals for stable operation in high-power industrial motor control environments.

Emerson Phoenix Contact 1X00102H01 is an Ovation DCS power distribution module that delivers protected 5V, 12V, and 24V DC power to controller and I/O modules with diagnostic support.

ENM MT101R is a self-powered electric motor hour meter for AC or DC motors. It uses an external sensor on a 4 ft cable to detect motor magnetic field and display true motor run time.

HYDAC HDA 3405-C-400-130 pressure transmitter with 0 to 400 bar relative pressure range, G 1/4 A process connection, and 4-pole Binder series 714 M18 electrical connection.

The Mitsubishi FR-A7N-ETH is an internal Ethernet communication option card for Mitsubishi 700-series adjustable speed drives. It provides multiprotocol Ethernet connectivity for industrial automation networks and supports configuration and monitoring through an embedded web server interface.

The ABB RDIO-01 is a digital I/O extension module designed for use with ABB drive systems. It provides three digital inputs and two relay outputs for expanding control and monitoring functions within compatible ABB drive architectures.