Search results for: 'taxable for'

The Hydrajaws M0095 Long Stroke Roofing Screw Tester Kit determines the strength and suitability of fixings in built-up roofing constructions where performance data is unavailable. The long stroke of 3.15'' means that once tested the fixing can be completely extracted.

The M35+ bridge leg extensions are an optional extra that extends the bridge's height capacity by 96mm.

The Hydrajaws Safety Post and Foundation Push Tester is designed to apply hydraulic pressure on a VRS safety post. This pressure is applied in increments through the use of a hand pump and its attached gauge. The distance between a set vertical datum and the safety post is then recorded at each stage.

The Hydrajaws Hydraulic Hollow Cylinder Tester Kit consists of a two-speed manually operated aluminium hand pump, digital gauge, 3m hose and either 180kN, 370kN or 500kN hollow bore aluminium cylinder which is more portable and weighs less than a traditional steel cylinder.

The Hydrajaws Wall Tie Tester Kit MK2 is used for testing all types of remedial wall tie. Trusted by market-leading companies, the Wall Tie Tester Kit is an essential tool for carrying out testing procedures in line with BRE Digest 401. Manufactured to exacting high standards, the Hydrajaws Wall Tie Tester Kit contains a small bolt tester adaptor and two threaded rod adaptors (M5 and M6) to test up to a maximum tensile load of 10kN. The three-legged load spreading bridge keeps reaction loads away from the fixing allowing results to be more consistent.

Compact, cordless design for portability Safety cap turns off device when in place Heats up to temperature in 15-20 seconds Temperature up to 450°C/840°F Maintains soldering temperature at least 300°C/600°F Lead free solder wire (Ø1mm ) included Requires 3 x AA Batteries (not included)

Drive: 1/2"/12.7mm Square Unit: N-m/lbf.in Dual units Torque Range: 40~200 N-m/ 33~144 lbf.ft Accuracy: +/-3.0 % Graduation: 1.0 N-m Gear teeth: 32 T OAL: 21"

The Hydrajaws Hydraulic Hollow Cylinder Tester Kit consists of a two-speed manually operated aluminium hand pump, digital gauge, 3m hose and either 180kN (40466lbf), 370kN (83179lbf) or 500kN (112405lbf) hollow bore aluminium cylinder which is more portable and weighs less than a traditional steel cylinder.

Hydrajaws 200-009 M2000 PRO Imperial Digital Tester Kit delivers 0-25kN/5620lbf pull testing for anchors and fixings with a digital gauge, 50mm stroke, and a universal adaptor set.

he HYTORC LST-3000 Lithium Series II is a 36V battery-powered electric torque tool rated up to 3,000 ft-lb. It features a brushless DC motor, TorcSense™ direct torque measurement, and a high-resolution rear display for controlled tightening and loosening of industrial fasteners using conventional reaction-arm configurations.

Hydrajaws M2000 Material Bond Tester Kit brings precise 25kN pull-off testing to concrete, screeds, coatings, laminates, plastics, paints, and enamels in lab, workshop, and on-site workflows.

Hydrajaws M2000 scaffold tie tester kit supports 0-25kN pull testing for scaffold anchors, with analogue and digital gauge options.

For M16 nuts, the bolt tester adaptor directly engages the nut in the pulling jaw.

Hydrajaws Heavy Duty Threaded Stud Adaptor provides reliable anchor testing support for threaded sleeve and stud anchors, helping deliver accurate pull testing across compatible sizes.

1 x Hydrajaws Threaded Stud Adaptor

The Hydrajaws standard digital gauge provides many advantages over the standard analogue gauge including more accurate and clearer results.