Search results for: 'open'

The Siemens 3TX4422-0A SIRIUS auxiliary contact block features 2NO + 2NC instantaneous contacts with screw-type terminals. Designed for use with contactor relays and power contactors according to EN 50011, it supports snap-on mounting, IP20 front protection, and positively driven operation per IEC 60947-5-1.

Siemens 771-8STF1 current-to-pneumatic (I/P) transducer converts a DC mA input to a proportional pneumatic output. Configuration: 4–20 mA input, 3–27 psig output, standard output capacity, terminal strip, intrinsically safe approval.

The General Electric CR104PLT43 is a 30.5mm push-to-test indicator light designed for 240V AC industrial automation systems. Part of the GE CR104P series, it utilizes a resistor power supply and supports machine-tool and control panel applications where manual lamp verification is required.

The GE Fanuc IC693CHS392G is a 10-slot expansion I/O baseplate for the Series 90-30 PLC platform. It features a 25-pin D-type expansion connector, rack address DIP switch, and supports local I/O expansion up to 50 feet. Designed for use with compatible CPU baseplates.

The AEG SH 05.31 is a 4-pole auxiliary contactor from the SH 05 series with a 24V DC coil. It features a 3NO + 1NC contact configuration (31E) and screw terminals. Rated per AC-15 and DC-13 utilization categories as specified in the AEG 2014 extract catalogue.

The Delta AFB1224HE is a 24V DC brushless axial cooling fan designed for reliable airflow in electronic and industrial equipment. It features dual ball bearings, locked rotor protection, and a 120 × 120 × 38 mm frame for consistent thermal management applications.

The Universal 447-LR-TC-P is a 120V magnetic fluorescent ballast designed to operate two lamps in trigger-start configurations. It supports F20T12, F15T8, and F15T12 lamps and features a low power factor, lag-type circuit. UL and CSA certifications support indoor and Type 1 outdoor use.

The Eaton H2006B-3 is a Freedom NEMA heater coil set designed for thermal overload protection in motor control applications. This Class 20 standard trip heater pack supports selectable full load current settings from 1.79A to 2.9A via dial positions A–D and is supplied as a factory-calibrated set of three elements.

The Omron MY4Z DC24(S) is a general-purpose miniature power relay with a 4PDT contact configuration and 24 VDC coil. Rated for 5 A switching in four-pole applications, it is designed for sequence control and power switching in industrial control systems.

The KAMAN Sensors digiVIT 855949-000 is a self-tuning digital driver for non-contact inductive and eddy current position and displacement sensors. It features pushbutton calibration, embedded intelligence, selectable analog outputs, and Ethernet connectivity for monitoring and parameter switching.

The MIP LM 3086 EPA3 is a laser-based opacity and dust monitor designed for continuous emissions monitoring in industrial stacks. It uses a single-pass, dual-path laser architecture with an optical reference path to measure opacity, optical density, and calibrated dust concentration values.

Honeywell 380-01873-100 I/O Interface Module enables remote monitoring and control of field devices using RS485 Panel Bus™ communication with 34 configurable I/O points for scalable building automation systems.

The General Electric DS200DDTBG2ABB is an LCI Auxiliary I/O Terminal Board for GE Mark V Speedtronic gas and steam turbine control systems. It provides auxiliary signal termination, conditioning, and isolation for analog and digital I/O in high-voltage industrial control environments.

This CCC Series 4 temperature input module set includes one IOM TCW (I-1/201-2/200) and one EIOM TCW (E-1/202-3/200). Both modules are designed for 3-wire GDC RTD temperature inputs and chassis mounting within CCC Series 4 control systems.

The Square D 8501NR61 is an 11-pin plug-in relay socket designed for use with compatible Square D relays and timers. It features single-tier screw clamp terminals and supports both panel and DIN rail mounting for industrial control applications.

Allen-Bradley 1336-RLOAD-SP2A load resistor module engineered for 1336 PLUS, PLUS II, FORCE, and IMPACT drives, providing controlled regenerative and braking energy dissipation in supported voltage ranges.

Allen-Bradley 1336-RLOAD-SP5A load resistor designed for 1336 adjustable frequency drives. Supports 575V operation in Frame E systems rated 150–300 HP for controlled load management.

Allen-Bradley 1336-T-SP5A control transformer designed for 1336 PLUS, PLUS II, Force, and Impact drives, supporting 150–250 HP systems at 460 VAC with stable internal control power delivery.

Allen-Bradley 50388 Driver PCB Board provides signal conditioning and drive interface control for compatible Allen-Bradley automation systems, supporting reliable communication between logic modules and field devices.

Metso Automation PDP406 Distributed Processing Unit for MAX DCS delivers real-time control, alarming, and data processing for industrial automation systems requiring reliable distributed architecture.

Allen-Bradley S50403 driver board designed for 1334 series AC drives, supporting 30–50 HP motor control. This replacement PCB regulates motor speed and torque through controlled voltage and frequency output.

Allen-Bradley 700-P000A1 Bulletin 700 Type P AC control relay built for machine tool and switchboard control. Features a 110–120V AC coil, 10A rating, and flexible DIN rail or panel mounting.

Allen-Bradley 800H-R3HA7 explosion-proof selector switch station with HAND-OFF-AUTO operation, built in a Type 7 & 9 aluminum enclosure for Class I, II, and III hazardous industrial locations.

Allen-Bradley 1336-CONV-SP4A converter power module designed for 1336 series adjustable frequency AC drives. Supports three-phase motor control applications within compatible 1336 drive platforms.