Search results for: 'automaker'

Banner Engineering BAT2.53S is a BAT Series glass fiber optic sensor with diffuse sensing mode and a right-angle threaded sensing tip. It features a stainless steel monocoil sheath, brass sensing end, 4 mm core diameter, and 0.914 m fiber length for demanding industrial sensing environments.

The Honeywell 621-9938RC is a dual-port Serial I/O Module for the IPC 620/621 Programmable Controller System. It provides redundant serial communication, configurable I/O point allocation, DIP switch configuration, front status LEDs, and supports hot-swappable operation in redundant serial I/O architectures.

The Allen-Bradley 442G-MABE1 Escape Release Module with Handle is a safety accessory for the Guardmaster 442G Multifunctional Access Box. It allows personnel to open a locked safety guard from inside a safeguarded area without tools, supporting emergency exit functionality.

The Honeywell 620-0081 Highway Interface Module (HIM) is a communication module used to connect Honeywell IPC 620 series controllers with TDC 2000/3000 Distributed Control Systems. It supports Data Hiway communication at 1.25 Mbps and is designed for rack-mounted installation in IPC 620 systems.

This CCC Series 4 temperature input module set includes one IOM TCW (I-1/201-2/200) and one EIOM TCW (E-1/202-3/200). Both modules are designed for 3-wire GDC RTD temperature inputs and chassis mounting within CCC Series 4 control systems.

Allen-Bradley 1336-RLOAD-SP2A load resistor module engineered for 1336 PLUS, PLUS II, FORCE, and IMPACT drives, providing controlled regenerative and braking energy dissipation in supported voltage ranges.

Allen-Bradley S50403 driver board designed for 1334 series AC drives, supporting 30–50 HP motor control. This replacement PCB regulates motor speed and torque through controlled voltage and frequency output.

Honeywell R4138D 1016 flame safeguard control designed for industrial burners and boilers. Provides supervised ignition sequencing, flame monitoring, and safety shutdown on flame failure.

Emerson Phoenix Contact 1X00102H01 is an Ovation DCS power distribution module that delivers protected 5V, 12V, and 24V DC power to controller and I/O modules with diagnostic support.

Allen-Bradley 1336-BDB-SP4C Gate Drive PCB designed for 1336 series variable frequency drives, supporting 20 HP and 460 VAC operation for reliable drive control and power regulation.

Toshiba VT130H9U4055 H9 drive delivers precise 5HP 460V 3PH motor control with vector control, motor-over-flux braking, and NEMA 1 industrial reliability.

The Westinghouse 5X00070G33 delivers precise multi-channel voltage signal acquisition for Ovation DCS environments, supporting ±5V and ±10V inputs with isolated channels and high-resolution data capture for reliable industrial monitoring.

Emerson DeltaV KJ3001X1-BD1 discrete input module for 120 VAC dry contact monitoring. This 8-channel module provides front-panel status indication and installs on DeltaV I/O hardware.

The Emerson KJ2006X1-BK1 Virtual I/O Module (VIM) is designed for DeltaV Safety Instrumented Systems (SIS) with CHARM I/O technology. It simulates up to 96 individually addressable I/O channels for offline system development, logic validation, commissioning preparation, and operator training without physical field wiring.

The Dwyer AP-7021-153-39 is a diaphragm operated pressure switch with an adjustable 10 to 125 psig range. It uses an SPDT snap acting switch in a general-purpose enclosure and is designed for air, non-corrosive gases, or compatible liquids.

The ABB Bailey IMASI02 is an Analog Slave Input module for the Infi 90 Process Management System. It converts analog field signals into digital data for processing by a Multi-Function Processor and interfaces up to fifteen process signals through a single MMU slot.

The ABB Bailey IMFCS01 is an intelligent Frequency Counter Slave Module for INFI 90 and Net 90 DCS platforms. It processes high-speed pulse inputs from field sensors and communicates frequency and period data to a Multi-Function Processor via the slave expander bus for speed monitoring and control.

The Yamatake Honeywell J-HMM00 is a high-level analog input module designed for Distributed Control System (DCS) architectures. Operating on 24 VDC with 60 mA current consumption, it supports multi-point analog signal acquisition for integration within compatible control systems such as MSC10.

The Bently Nevada 16699-03-05-03 is a velocity seismoprobe vibration sensor used for industrial condition monitoring. It converts mechanical vibration into an electrical signal and is designed for housing-mounted vibration measurement on rotating machinery. The sensor features a metal cylindrical body, stud mounting, and a top-mounted three-screw terminal block for field wiring.

Fluke 820-2 LED Stroboscope enables non-contact rotational speed diagnostics with high-intensity LED output, quartz accuracy, and sharp stop-motion imaging.

Toshiba VF-S11-4015PL-WN industrial inverter delivers precise speed control for 3-phase induction motors, supporting 1.5kW operation on 380–500V systems with compact panel-mount design and flexible control modes.

Alstom ESA-700 UV flame signal analyzer for Limelight Exacta systems, providing fast flame failure detection and reliable burner monitoring in large combustion equipment using 21.6–26V AC input power.

Allen-Bradley S50411-002 dynamic brake board enables controlled motor deceleration by managing regenerative energy through external brake resistors in compatible 1305 variable frequency drives.

Allen-Bradley 1334-MOD-W3 run/fault contact mod kit adds isolated relay outputs for remote drive status monitoring on Bulletin 1334 and 1335 AC drives, supporting external control and annunciation systems.